gtr-04h(v.2) восстановление прошивки

Аналоговые системы видеонаблюдения. Камеры, регистраторы, мониторы, блоки питания и т.п.
Ответить
Limonchik
Новичок
Сообщения: 11
Зарегистрирован: 06 ноя 2017, 09:40

gtr-04h(v.2) восстановление прошивки

Сообщение Limonchik » 01 фев 2018, 08:04

добрый день форумчане. скачав прошивку с оф сайто попытался прошить её в регистратор, после чего он только показывает начальную картинку и ребутится. как оказалось на сайте лежала прошивка старее чем та что была в регистраторе, возможно по этому он и помер. подключившись к нему через терминал (свсем недавно восстанавливал прошивку на старенькой точке доступа и решил попробовать зацепится таким же способом к регистратору) вижу что бут живой и пытается что то грузить.
единственное что мне удалось это отправить обновлённую прошивку (предоставила поддержка сайта) на регистратор командой get tftp, но как заставить регистратор её применить не знаю, в линуксе ни бумбум.

Limonchik
Новичок
Сообщения: 11
Зарегистрирован: 06 ноя 2017, 09:40

Re: gtr-04h(v.2) восстановление прошивки

Сообщение Limonchik » 01 фев 2018, 08:05

вот что он выдаёт по ctrl+c

Код: Выделить всё

U-Boot 2010.06 (Sep 24 2013 - 20:39:26


************************************************

U_BOOT:7204XQ_VA UBOOT  T20130924 20:39:19

************************************************

main_board_ver 0

DRAM:  256 MiB

Check spi flash controller v300. found

Spi(cs1) ID: 0x01 0x20 0x18 0x4D 0x01 0x80

Get match S25FL129P1/S25FL128S 0x1C 0x0

Spi(cs1): Block:64KB Chip:16MB Name:"S25FL127S1"

*** Warning - bad CRC, using default environment



In:    serial

Out:   serial

Err:   serial

judge ddr init

user init finish.

Hit CTRL + C to stop autoboot:  0

Streaming3520A # <INTERRUPT>

Streaming3520A # <INTERRUPT>

Streaming3520A # help

?       - alias for 'help'

base    - print or set address offset

bootm   - boot application image from memory

bootp   - boot image via network using BOOTP/TFTP protocol

cmp     - memory compare

cp      - memory copy

crc32   - checksum calculation

decjpg  - jpgd   - decode jpeg picture.



ext2load- load binary file from a Ext2 filesystem

ext2ls  - list files in a directory (default /)

fatinfo - print information about filesystem

fatload - load binary file from a dos filesystem

fatls   - list files in a directory (default /)

fatwrite- write file into a dos filesystem

getinfo - print hardware information

go      - start application at address 'addr'

help    - print command description/usage

loadb   - load binary file over serial line (kermit mode)

loady   - load binary file over serial line (ymodem mode)

loop    - infinite loop on address range

md      - memory display

mii     - MII utility commands

mm      - memory modify (auto-incrementing address)

mtest   - simple RAM read/write test

mw      - memory write (fill)

nm      - memory modify (constant address)

ping    - send ICMP ECHO_REQUEST to network host

printenv- print environment variables

rarpboot- boot image via network using RARP/TFTP protocol

reset   - Perform RESET of the CPU

saveenv - save environment variables to persistent storage

setenv  - set environment variables

setvobg - setvobg   - set vo backgroud color.

        - setvobg [dev color]

sf      - SPI flash sub-system

startgx - startgx   - open graphics layer.

        - startgx [layer addr stride x y w h]



startvo - startvo   - open interface of vo device.

        - startvo [dev type sync]

stopgx  - stopgx   - close graphics layer.

        - stopgx [layer]

stopvo  - stopvo   - close interface of vo device.

        - stopvo [dev]

tftp    - tftp  - download or upload image via network using TFTP protocol

usb     - USB sub-system

usbboot - boot from USB device

version - print monitor version

Streaming3520A # print

bootargs=mem=92M console=ttyAMA0,115200 UartConfig=1 EtherConfig=1 root=/dev/mtdblock2 rootfstype=squashfs mtdparts=hi_sfc:640K(boot+3Logo),1792K(Kernel),13M(Root+App),64K(SysConfig),64K(SysStatus),512K(SysPara)

bootcmd=sf probe 0;sf read 0x82000000 0xA0000 0x1C0000;bootm 0x82000000

bootdelay=1

baudrate=115200

ethaddr=00:09:24:**:**:**
ipaddr=192.168.2.234

serverip=192.168.2.56

netmask=255.255.254.0

bootfile="uImage"

stdin=serial

stdout=serial

stderr=serial
вот лог загрузки

Код: Выделить всё

U-Boot 2010.06 (Sep 24 2013 - 20:39:26)



************************************************

U_BOOT:7204XQ_VA UBOOT  T20130924 20:39:19

************************************************

main_board_ver 0

DRAM:  256 MiB

Check spi flash controller v300. found

Spi(cs1) ID: 0x01 0x20 0x18 0x4D 0x01 0x80

Get match S25FL129P1/S25FL128S 0x1C 0x0

Spi(cs1): Block:64KB Chip:16MB Name:"S25FL127S1"

*** Warning - bad CRC, using default environment



In:    serial

Out:   serial

Err:   serial

judge ddr init

user init finish.

Hit CTRL + C to stop autoboot:  0

16384 KiB hi_sfc at 0:0 is now current device



[MachineTypeCheck, 1692]:DeviceType 24



[UpgradeSoftware, 1709]:Check Upgrade At Momory Address 0x00000000



[VerifyMmpValid, 229]:Bad memory Addr 0x00000000



[CommonUpgrade, 1230]:Invalid Upgrade Addr 0x00000000



USB:   scanning bus for devices... 1 USB Device(s) found

0 Storage Device(s) found

No device found. Not initialized?

USB:   scanning bus for devices... 1 USB Device(s) found

0 Storage Device(s) found

No device found. Not initialized?

USB:   scanning bus for devices... 1 USB Device(s) found

0 Storage Device(s) found

No device found. Not initialized?

[USBSoftwareUpgrade, 309]:SoftwareUpgrade: Cann't Initialize Usb Devices for Upgrade



[UpgradeSoftware, 1719]:USBSoftwareUpgrade: No Upgrade



[UpgradeSoftware, 1728]:Free Flash



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



[HAL_LAYER_EnableLayer, 3205]:pVoReg->G0CTRL.u32 0x205C9000



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



graphic layer 0 closed!

dev 0 closed!

16384 KiB hi_sfc at 0:0 is now current device



jpeg decoding ...

<<addr=0x83000000, size=0x20000, vobuf=0x8f400000>>

mmu_enable

<<imgwidth=1024, imgheight=768, linebytes=2048>>

decode success!!!!

dev 0 opened!

[HAL_LAYER_EnableLayer, 3205]:pVoReg->G0CTRL.u32 0x205C9000



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



graphic layer 0 opened!



jpeg decoding ...

<<addr=0x83000000, size=0x20000, vobuf=0x8f000000>>

mmu_enable

<<imgwidth=720, imgheight=576, linebytes=1440>>

decode success!!!!

decode jpeg!

dev 2 opened!

[HAL_LAYER_EnableLayer, 3205]:pVoReg->G0CTRL.u32 0x205C9000



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



graphic layer 2 opened!

## Booting kernel from Legacy Image at 82000000 ...

   Image Name:   Linux-3.0.8

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    1336772 Bytes = 1.3 MiB

   Load Address: 80008000

   Entry Point:  80008000

   Loading Kernel Image ... OK

OK



Starting kernel ...



Uncompressing Linux... done, booting the kernel.

Linux version 3.0.8 (root@ubuntu) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #82 Sun Sep 15 21:20:22 PDT 2013

CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f

CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

Machine: godarm

Memory policy: ECC disabled, Data cache writeback

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 23368

Kernel command line: mem=92M console=ttyAMA0,115200 UartConfig=1 EtherConfig=1 root=/dev/mtdblock2 rootfstype=squashfs mtdparts=hi_sfc:640K(boot+3Logo),1792K(Kernel),13M(Root+App),64K(SysConfig),64K(SysStatus),512K(SysPara)

UartConfig_setup:1(1)

EtherConfig_setup:1(1)[0: 3521==>7216XH_VA 8608XH_VA; 1: 3520A==>8604XQ_VA]; 2: 3521 NVR; 3: 3520A NVR

PID hash table entries: 512 (order: -1, 2048 bytes)

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory: 92MB = 92MB total

Memory: 89596k/89596k available, 4612k reserved, 0K highmem

Virtual kernel memory layout:

    vector  : 0xffff0000 - 0xffff1000   (   4 kB)

    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)

    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)

    vmalloc : 0xc6000000 - 0xfe000000   ( 896 MB)

    lowmem  : 0xc0000000 - 0xc5c00000   (  92 MB)

    modules : 0xbf000000 - 0xc0000000   (  16 MB)

      .init : 0xc0008000 - 0xc0025000   ( 116 kB)

      .text : 0xc0025000 - 0xc0359000   (3280 kB)

      .data : 0xc035a000 - 0xc0376b00   ( 115 kB)

       .bss : 0xc0376b24 - 0xc03a47c0   ( 184 kB)

SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

NR_IRQS:128 nr_irqs:128 128

sched_clock: 32 bits at 155MHz, resolution 6ns, wraps every 27709ms

sched_clock: wrong multiply/shift: 432960413>>26 vs calculated 3463683303>>29

sched_clock: fix multiply/shift to avoid scheduler hiccups

Console: colour dummy device 80x30

Calibrating delay loop... 1849.75 BogoMIPS (lpj=9248768)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

Serial: AMBA PL011 UART driver

uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2

console [ttyAMA0] enabled

uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2

uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2

uart:3: ttyAMA3 at MMIO 0x200b0000 (irq = 43) is a PL011 rev2

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Switching to clocksource timer1

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

NetWinder Floating Point Emulator V0.97 (double precision)

L2cache cache controller enabled

squashfs: version 4.0 (2009/01/31) Phillip Lougher

fuse init (API version 7.16)

msgmni has been set to 174

Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)

io scheduler noop registered

io scheduler deadline registered (default)

io scheduler cfq registered

brd: module loaded

loop: module loaded

ahci: SSS flag set, parallel bus scan disabled

ahci ahci.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl platform mode

ahci ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc sxs boh

scsi0 : ahci_platform

scsi1 : ahci_platform

ata1: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x100 irq 68

ata2: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x180 irq 68

Spi id table Version 1.22

Hisilicon Spi Flash Controller V300 New Device Driver, Version 1.10

Check Spi Flash Controller V300 New.

Found

Spi(cs1) ID: 0x01 0x20 0x18 0x4D 0x01 0x80

Get match S25FL129P1/S25FL128S 0x1C 0x0

Spi(cs1):

Block:64KB

Chip:16MB

Name:"S25FL127S1"

[hisfc300_probe, 1019]: Install Lock & unLock func V2.0



6 cmdlinepart partitions found on MTD device hi_sfc

Creating 6 MTD partitions on "hi_sfc":

0x000000000000-0x0000000a0000 : "boot+3Logo"

0x0000000a0000-0x000000260000 : "Kernel"

0x000000260000-0x000000f60000 : "Root+App"

0x000000f60000-0x000000f70000 : "SysConfig"

0x000000f70000-0x000000f80000 : "SysStatus"

0x000000f80000-0x000001000000 : "SysPara"

Fixed MDIO Bus: probed

STMMAC driver:

        platform registration...

        done!

Set system config register 0x200300ec with value 0x003f003f

        done!

        DWMAC1000 - user ID: 0x10, Synopsys ID: 0x36

        Enhanced descriptor structure

MACADDR in get is 0:0:0:0:0:0

        no valid MAC address for MAC 0;please, use ifconfig or nwhwconfig!

        eth0 - (dev. name: stmmaceth - id: 0, IRQ #119

        IO base addr: 0xc6140000)

Register STMMAC MII Bus for 1

STMMAC MII Bus: probed

eth0: PHY ID 00008201 at 1 IRQ -6 (1:01) active

stmmac_reset: RESET COMPLETE!



**************************************************

*  TNK driver built on Sep 15 2013 at 21:16:16

*  TNK driver mode is BYPASS

**************************************************

stmmac: Rx Checksum Offload Engine supported

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

NET: Registered protocol family 24

usbcore: registered new interface driver asix

usbcore: registered new interface driver cdc_ether

usbcore: registered new interface driver net1080

usbcore: registered new interface driver rndis_host

usbcore: registered new interface driver cdc_subset

usbcore: registered new interface driver zaurus

cdc_ncm: 04-Aug-2011

usbcore: registered new interface driver cdc_ncm

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

hiusb-ehci hiusb-ehci.0: HIUSB EHCI

hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1

hiusb-ehci hiusb-ehci.0: irq 63, io mem 0x100b0000

hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

hiusb-ohci hiusb-ohci.0: HIUSB OHCI

hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2

hiusb-ohci hiusb-ohci.0: irq 64, io mem 0x100a0000

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

usbcore: registered new interface driver cdc_wdm

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

usbcore: registered new interface driver ums-alauda

usbcore: registered new interface driver ums-datafab

usbcore: registered new interface driver ums-freecom

ata1: SATA link down (SStatus 0 SControl 300)

usbcore: registered new interface driver ums-isd200

usbcore: registered new interface driver ums-jumpshot

usbcore: registered new interface driver ums-sddr09

usbcore: registered new interface driver ums-sddr55

usbcore: registered new interface driver mdc800

mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera

usbcore: registered new interface driver usbserial

usbserial: USB Serial Driver core

USB Serial support registered for GSM modem (1-port)

usbcore: registered new interface driver option

option: v0.7.2:USB Driver for GSM modems

mousedev: PS/2 mouse device common for all mice

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP cubic registered

Initializing XFRM netlink socket

NET: Registered protocol family 17

NET: Registered protocol family 15

Registering the dns_resolver key type

registered taskstats version 1

▒ata2: SATA link down (SStatus 0 SControl 300)

VFS: Mounted root (squashfs filesystem) readonly on device 31:2.

Freeing init memory: 116K


init started: BusyBox v1.16.1 (2012-11-13 16:20:01 CST)


starting pid 451, tty '': '/etc/init.d/rcS'

***************************************************

 BusyBox: 8608XQ_VA ROOTFS  NTPL T20121016 10:54:31

***************************************************

udevd (459): /proc/459/oom_adj is deprecated, please use /proc/459/oom_score_adj instead.

Hisilicon Media Memory Zone Manager

hi3520A_base: module license 'Proprietary' taints kernel.

Disabling lock debugging due to kernel taint

Hisilicon UMAP device driver interface: v3.00

load sys.ko for Hi3520A...OK!

Load tde.ko ...OK!

load venc.ko for Hi3520A...OK!

load group.ko for Hi3520A...OK!

load chnl.ko for Hi3520A...OK!

load h264e.ko for Hi3520A...OK!

load rc.ko ....OK!

load jpege.ko for Hi3520A...OK!

load vou.ko ....OK!

load vpss.ko ....OK!

load vda.ko ....OK!

load region.ko ....OK!

load vdec.ko ....OK

load vhd firmware.ko OK

load hdmi.ko ....OK!

Load jpeg6b.ko success.         (SDK_VERSION:[jpeg6bv1.0] Build Time:[Nov 28 2012, 18:48:49])

eth0: generated random MAC address 96:c3:af:7b:7e:1d

MACADDR in set is 96:c3:af:7b:7e:1d

Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 1)

Welcome to Streaming Linux.

mount: mounting /dev/mtdblock8 on /usr/local failed: No such device

Run App Finish


starting pid 735, tty '': '/sbin/getty -L ttyS000 115200 vAuto login as root ...

Jan  1 00:00:03 login[735]: root login on 'ttyS000'






BusyBox v1.16.1 (2012-11-13 16:20:01 CST) built-in shell (ash)

Enter 'help' for a list of built-in commands.



Welcome to Streaming Linux.

None of nfsroot found in cmdline.

# Start cash language

create folder /tmp/webcash

Get config json

[GetSystemCfgJson-GetFileSize] len 40, {

    "DataLen":12978,

    "DataCrc":44

}

Start Cash web.config

result={"APP_TYPE":"formal","BUZZER_ENABLE":null,"CHANNEL_NUM":4,"CUSTOMER_ID":0,"CUSTOMER_NAME":"CUSTOMER_04323","DDNS":[{"SELECT":"true","TYPE":"REELINK","VALUE":24},{"SELECT":"true","TYPE":"88110","VALUE":16},{"SELECT":"true","TYPE":"3322","VALUE":0},{"SELECT":"true","TYPE":"DYNDNS","VALUE":1},{"SELECT":"false","TYPE":"LTSCCTV","VALUE":2},{"SELECT":"false","TYPE":"LOREXDDNS","VALUE":3},{"SELECT":"true","TYPE":"DNSEXIT","VALUE":4},{"SELECT":"false","TYPE":"MYQ-SEE.COM","VALUE":5},{"SELECT":"false","TYPE":"ANPVISION","VALUE":6},{"SELECT":"false","TYPE":"VISIONICA","VALUE":7},{"SELECT":"false","TYPE":"JINSANJIA","VALUE":8},{"SELECT":"false","TYPE":"CCTVGOV","VALUE":9},{"SELECT":"false","TYPE":"NIGHTOWL","VALUE":10},{"SELECT":"false","TYPE":"FFBBCC","VALUE":11},{"SELECT":"false","TYPE":"ZHIJING","VALUE":12},{"SELECT":"true","TYPE":"NO-IP","VALUE":13},{"SELECT":"true","TYPE":"CHANGEIP","VALUE":15},{"SELECT":"false","TYPE":"DDNSDVR","VALUE":17},{"SELECT":"false","TYPE":"PORTAL ECOTRONIC","VALUE":18},{"SELECT":"false","TYPE":"DFSEC","VALUE":19},{"SELECT":"false","TYPE":"SANLLON.COM","VALUE":20},{"SELECT":"false","TYPE":"WISOL","VALUE":21},{"SELECT":"false","TYPE":"88110_NIGHTOWL","VALUE":22},{"SELECT":"false","TYPE":"CAMSEC","VALUE":23},{"SELECT":"false","TYPE":"UNICAM","VALUE":25},{"SELECT":"false","TYPE":"SECURUS","VALUE":26},{"SELECT":"false","TYPE":"LINKDVR","VALUE":27},{"SELECT":"false","TYPE":"IPCAMEYE.NET","VALUE":28}],"DEVICE_ALARM_OUTPUT":1,"DEVICE_AUDIO_NUM":4,"ENC_RESOURCE":[{"NTSC_TOTAL_RES":480,"PAL_TOTAL_RES":400,"TYPE":"MAINSTREAM","UNIT":"CIF-FRAME"},{"NTSC_TOTAL_RES":120,"PAL_TOTAL_RES":100,"TYPE":"SUBSTREAM","UNIT":"CIF-FRAME"},{"NTSC_TOTAL_RES":24,"PAL_TOTAL_RES":24,"TYPE":"MOBILESTREAM","UNIT":"CIF-FRAME"}],"FTP_SWITCH":"false","HDD_NUM":1,"IE_CUR_LAN":null,"IE_LOGDIR":"IE_04.323.png","IE_LOGIN_LOG":"logo_viewdvr.png","IE_MAINSTREAM_SELECT":null,"IE_NIGHT_CUSTOMER_LOGO":null,"IE_OCXVER":"V1216#version=1,2,1,6","IE_PLAYBACK_NUM":null,"IE_PRIWE":"true","LOG_SWITCH":"true","MAX_ONLINE_USER_NUM":4,"MOBSTREAM_RES":null,"NET_3G":"true","NET_CMS":"false","NET_WIFI":"false","PREVIEW_PERMISSION":null,"PRODUCT_TYPE":"7204XQ_VA","RAILWAY_SWITCH":null,"REC_RES":[{"SELECT":"true","TYPE":"CIF","VALUE":0},{"SELECT":"true","TYPE":"HD1","VALUE":1},{"SELECT":"true","TYPE":"D1","VALUE":2},{"SELECT":"true","TYPE":"WCIF","VALUE":11},{"SELECT":"true","TYPE":"WHD1","VALUE":12},{"SELECT":"true","TYPE":"WD1(960H)","VALUE":13},{"SELECT":"false","TYPE":"720P","VALUE":6},{"SELECT":"false","TYPE":"1080P","VALUE":7}],"SENSOR_NUM":4,"SG_PLATFORM":null,"SPOT_SWITCH":"false","SUBSTREAM_RES":null,"SUPPORT_960H":null,"SUPPORT_IRREGULAR_SPLIT":"true","SUPPORT_RAID":null,"TEMPER_ALARM_SWITCH":null,"TIME_SYNC_SERVER":[{"NAME":"time.windows.com"},{"NAME":"time.nist.gov"},{"NAME":"time-nw.nist.gov"},{"NAME":"time-a.nist.gov"},{"NAME":"time-b.nist.gov"}],"Talkback":"false","UI_FRAMERATE_CFG":[{"NAME":"PAL","VALUE":25},{"NAME":"NTSC","VALUE":30}],"UI_LANG_CFG":[{"CFG_FILE":"ui/language/chinese.ini","FONT_LIB":"FZYaoTi","FONT_LIB_FILE":"fonts/FZYTK.TTF","ICON_DIR":"ui/icons/chinese","LANG":"中文","SELECT":"true","VALUE":0},{"CFG_FILE":"ui/language/english.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","LANG":"English","SELECT":"true","VALUE":1},{"CFG_FILE":"ui/language/korean.ini","FONT_LIB":"New Gulim","FONT_LIB_FILE":"fonts/NewGulim.ttf","ICON_DIR":"ui/icons/korean","LANG":"한국어","SELECT":"false","VALUE":2},{"CFG_FILE":"ui/language/italian.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/italian","LANG":"Italiano","SELECT":"true","VALUE":3},{"CFG_FILE":"ui/language/german.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/german","LANG":"Deutsch","SELECT":"false","VALUE":4},{"CFG_FILE":"ui/language/thai.ini","FONT_LIB":"Tahoma","FONT_LIB_FILE":"fonts/tahoma.ttf","ICON_DIR":"ui/icons/thai","LANG":"ไทย","SELECT":"false","VALUE":5},{"CFG_FILE":"ui/language/turkish.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/turkish","LANG":"Türkçe","SELECT":"false","VALUE":6},{"CFG_FILE":"ui/language/portuguese.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/portuguese","LANG":"Português","SELECT":"true","VALUE":7},{"CFG_FILE":"ui/language/spanlish.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/spanlish","LANG":"Español","SELECT":"true","VALUE":8},{"CFG_FILE":"ui/language/romanian.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/romanian","LANG":"Română","SELECT":"false","VALUE":9},{"CFG_FILE":"ui/language/greek.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","LANG":"Ελληνικά","SELECT":"false","VALUE":10},{"CFG_FILE":"ui/language/french.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/french","LANG":"Français","SELECT":"true","VALUE":11},{"CFG_FILE":"ui/language/russian.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/russian","LANG":"Русский","SELECT":"true","VALUE":12},{"CFG_FILE":"ui/language/nederlands.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","LANG":"Nederlands","SELECT":"false","VALUE":13},{"CFG_FILE":"ui/language/hebrew.ini","FONT_LIB":"Arial","FONT_LIB_FILE":"fonts/arial.ttf","ICON_DIR":"ui/icons/hebrew","LANG":"עברית","SELECT":"false","VALUE":14},{"CFG_FILE":"ui/language/chinesetrad.ini","FONT_LIB":"msf","FONT_LIB_FILE":"fonts/msf.ttf","ICON_DIR":"ui/icons/traditional","LANG":"中文繁体","SELECT":"false","VALUE":15},{"CFG_FILE":"ui/language/polish.ini","FONT_LIB":"CALIBRI","FONT_LIB_FILE":"fonts/CALIBRI.TTF","ICON_DIR":"ui/icons/polish","LANG":"Polski","SELECT":"false","VALUE":16}],"UI_SUB_FRAMERATE_CFG":[{"NAME":"PAL","VALUE":8},{"NAME":"NTSC","VALUE":10}]}



Cash web.config ok len=5890

Cash lan=中文 ini=./ui/language/chinese.ini

Cash base english path=./ui/language/english.ini

index=13

customini=./ui/language/CUSTOMER_04323_chinese.ini

=======start scandir src=../www/HAPPLE/pages/ dst=/tmp/webcash/中文/

=======start scandir src=../www/HAPPLE/pages/sysTips/ dst=/tmp/webcash/中文/sysTips/

=======start scandir src=../www/HAPPLE/pages/sysTips/tipsImg/ dst=/tmp/webcash/中文/sysTips/tipsImg/

=======start scandir src=../www/HAPPLE/pages/proxy/ dst=/tmp/webcash/中文/proxy/

Cash include file ../www/HAPPLE/pages/proxy/../liveView.html to /tmp/webcash/中文/proxy/, filename=../liveView.html, fd=0x13bad78

Cash include file ../www/HAPPLE/pages/proxy/../playback.html to /tmp/webcash/中文/proxy/, filename=../playback.html, fd=0x13bad78

Cash include file ../www/HAPPLE/pages/proxy/../left.html to /tmp/webcash/中文/proxy/, filename=../left.html, fd=0x13bad78

Cash include file ../www/HAPPLE/pages/liveView.html to /tmp/webcash/中文/, filename=liveView.html, fd=0x13bad78

Cash include file ../www/HAPPLE/pages/playback.html to /tmp/webcash/中文/, filename=playback.html, fd=0x13bad78

Cash include file ../www/HAPPLE/pages/left.html to /tmp/webcash/中文/, filename=left.html, fd=0x13bad78

=======start scandir src=../www/HAPPLE/pages/images/ dst=/tmp/webcash/中文/images/

=======start scandir src=../www/HAPPLE/pages/WAP/ dst=/tmp/webcash/中文/WAP/

=======start scandir src=../www/HAPPLE/pages/Styles/ dst=/tmp/webcash/中文/Styles/

=======start scandir src=../www/HAPPLE/pages/LoadPage/ dst=/tmp/webcash/中文/LoadPage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemMessage/ dst=/tmp/webcash/中文/LoadPage/SystemMessage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemManagement/ dst=/tmp/webcash/中文/LoadPage/SystemManagement/

=======start scandir src=../www/HAPPLE/pages/LoadPage/NetworkService/ dst=/tmp/webcash/中文/LoadPage/NetworkService/

=======start scandir src=../www/HAPPLE/pages/LoadPage/EncodingSetting/ dst=/tmp/webcash/中文/LoadPage/EncodingSetting/

=======start scandir src=../www/HAPPLE/pages/LoadPage/AlarmSet/ dst=/tmp/webcash/中文/LoadPage/AlarmSet/

=======start scandir src=../www/HAPPLE/pages/JS/ dst=/tmp/webcash/中文/JS/

Cash lan=English ini=./ui/language/english.ini

Cash base english path=./ui/language/english.ini

index=13

customini=./ui/language/CUSTOMER_04323_english.ini

=======start scandir src=../www/HAPPLE/pages/ dst=/tmp/webcash/English/

=======start scandir src=../www/HAPPLE/pages/sysTips/ dst=/tmp/webcash/English/sysTips/

=======start scandir src=../www/HAPPLE/pages/sysTips/tipsImg/ dst=/tmp/webcash/English/sysTips/tipsImg/

=======start scandir src=../www/HAPPLE/pages/proxy/ dst=/tmp/webcash/English/proxy/

Cash include file ../www/HAPPLE/pages/proxy/../liveView.html to /tmp/webcash/English/proxy/, filename=../liveView.html, fd=0x13bb360

Cash include file ../www/HAPPLE/pages/proxy/../playback.html to /tmp/webcash/English/proxy/, filename=../playback.html, fd=0x13bb360

Cash include file ../www/HAPPLE/pages/proxy/../left.html to /tmp/webcash/English/proxy/, filename=../left.html, fd=0x13bb360

Cash include file ../www/HAPPLE/pages/liveView.html to /tmp/webcash/English/, filename=liveView.html, fd=0x13bb360

Cash include file ../www/HAPPLE/pages/playback.html to /tmp/webcash/English/, filename=playback.html, fd=0x13bb360

Cash include file ../www/HAPPLE/pages/left.html to /tmp/webcash/English/, filename=left.html, fd=0x13bb360

=======start scandir src=../www/HAPPLE/pages/images/ dst=/tmp/webcash/English/images/

=======start scandir src=../www/HAPPLE/pages/WAP/ dst=/tmp/webcash/English/WAP/

=======start scandir src=../www/HAPPLE/pages/Styles/ dst=/tmp/webcash/English/Styles/

=======start scandir src=../www/HAPPLE/pages/LoadPage/ dst=/tmp/webcash/English/LoadPage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemMessage/ dst=/tmp/webcash/English/LoadPage/SystemMessage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemManagement/ dst=/tmp/webcash/English/LoadPage/SystemManagement/

=======start scandir src=../www/HAPPLE/pages/LoadPage/NetworkService/ dst=/tmp/webcash/English/LoadPage/NetworkService/

=======start scandir src=../www/HAPPLE/pages/LoadPage/EncodingSetting/ dst=/tmp/webcash/English/LoadPage/EncodingSetting/

=======start scandir src=../www/HAPPLE/pages/LoadPage/AlarmSet/ dst=/tmp/webcash/English/LoadPage/AlarmSet/

=======start scandir src=../www/HAPPLE/pages/JS/ dst=/tmp/webcash/English/JS/



language 한국어 is not select



Cash lan=Italiano ini=./ui/language/italian.ini

Cash base english path=./ui/language/english.ini

index=13

customini=./ui/language/CUSTOMER_04323_italian.ini

=======start scandir src=../www/HAPPLE/pages/ dst=/tmp/webcash/Italiano/

=======start scandir src=../www/HAPPLE/pages/sysTips/ dst=/tmp/webcash/Italiano/sysTips/

=======start scandir src=../www/HAPPLE/pages/sysTips/tipsImg/ dst=/tmp/webcash/Italiano/sysTips/tipsImg/

=======start scandir src=../www/HAPPLE/pages/proxy/ dst=/tmp/webcash/Italiano/proxy/

Cash include file ../www/HAPPLE/pages/proxy/../liveView.html to /tmp/webcash/Italiano/proxy/, filename=../liveView.html, fd=0x13db648

Cash include file ../www/HAPPLE/pages/proxy/../playback.html to /tmp/webcash/Italiano/proxy/, filename=../playback.html, fd=0x13db648

Cash include file ../www/HAPPLE/pages/proxy/../left.html to /tmp/webcash/Italiano/proxy/, filename=../left.html, fd=0x13db648

Cash include file ../www/HAPPLE/pages/liveView.html to /tmp/webcash/Italiano/, filename=liveView.html, fd=0x13daf28

Cash include file ../www/HAPPLE/pages/playback.html to /tmp/webcash/Italiano/, filename=playback.html, fd=0x13daf28

Cash include file ../www/HAPPLE/pages/left.html to /tmp/webcash/Italiano/, filename=left.html, fd=0x13daf28

=======start scandir src=../www/HAPPLE/pages/images/ dst=/tmp/webcash/Italiano/images/

=======start scandir src=../www/HAPPLE/pages/WAP/ dst=/tmp/webcash/Italiano/WAP/

=======start scandir src=../www/HAPPLE/pages/Styles/ dst=/tmp/webcash/Italiano/Styles/

=======start scandir src=../www/HAPPLE/pages/LoadPage/ dst=/tmp/webcash/Italiano/LoadPage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemMessage/ dst=/tmp/webcash/Italiano/LoadPage/SystemMessage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemManagement/ dst=/tmp/webcash/Italiano/LoadPage/SystemManagement/

=======start scandir src=../www/HAPPLE/pages/LoadPage/NetworkService/ dst=/tmp/webcash/Italiano/LoadPage/NetworkService/

=======start scandir src=../www/HAPPLE/pages/LoadPage/EncodingSetting/ dst=/tmp/webcash/Italiano/LoadPage/EncodingSetting/

=======start scandir src=../www/HAPPLE/pages/LoadPage/AlarmSet/ dst=/tmp/webcash/Italiano/LoadPage/AlarmSet/

=======start scandir src=../www/HAPPLE/pages/JS/ dst=/tmp/webcash/Italiano/JS/



language Deutsch is not select





language ไทย is not select





language Türkçe is not select



Cash lan=Português ini=./ui/language/portuguese.ini

Cash base english path=./ui/language/english.ini

index=13

customini=./ui/language/CUSTOMER_04323_portuguese.ini

=======start scandir src=../www/HAPPLE/pages/ dst=/tmp/webcash/Português/

=======start scandir src=../www/HAPPLE/pages/sysTips/ dst=/tmp/webcash/Português/sysTips/

=======start scandir src=../www/HAPPLE/pages/sysTips/tipsImg/ dst=/tmp/webcash/Português/sysTips/tipsImg/

=======start scandir src=../www/HAPPLE/pages/proxy/ dst=/tmp/webcash/Português/proxy/

Cash include file ../www/HAPPLE/pages/proxy/../liveView.html to /tmp/webcash/Português/proxy/, filename=../liveView.html, fd=0x13de8a8

Cash include file ../www/HAPPLE/pages/proxy/../playback.html to /tmp/webcash/Português/proxy/, filename=../playback.html, fd=0x13de8a8

Cash include file ../www/HAPPLE/pages/proxy/../left.html to /tmp/webcash/Português/proxy/, filename=../left.html, fd=0x13de8a8

Cash include file ../www/HAPPLE/pages/liveView.html to /tmp/webcash/Português/, filename=liveView.html, fd=0x13de8a8

Cash include file ../www/HAPPLE/pages/playback.html to /tmp/webcash/Português/, filename=playback.html, fd=0x13de8a8

Cash include file ../www/HAPPLE/pages/left.html to /tmp/webcash/Português/, filename=left.html, fd=0x13de8a8

=======start scandir src=../www/HAPPLE/pages/images/ dst=/tmp/webcash/Português/images/

=======start scandir src=../www/HAPPLE/pages/WAP/ dst=/tmp/webcash/Português/WAP/

=======start scandir src=../www/HAPPLE/pages/Styles/ dst=/tmp/webcash/Português/Styles/

=======start scandir src=../www/HAPPLE/pages/LoadPage/ dst=/tmp/webcash/Português/LoadPage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemMessage/ dst=/tmp/webcash/Português/LoadPage/SystemMessage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemManagement/ dst=/tmp/webcash/Português/LoadPage/SystemManagement/

=======start scandir src=../www/HAPPLE/pages/LoadPage/NetworkService/ dst=/tmp/webcash/Português/LoadPage/NetworkService/

=======start scandir src=../www/HAPPLE/pages/LoadPage/EncodingSetting/ dst=/tmp/webcash/Português/LoadPage/EncodingSetting/

=======start scandir src=../www/HAPPLE/pages/LoadPage/AlarmSet/ dst=/tmp/webcash/Português/LoadPage/AlarmSet/

=======start scandir src=../www/HAPPLE/pages/JS/ dst=/tmp/webcash/Português/JS/

Cash lan=Español ini=./ui/language/spanlish.ini

Cash base english path=./ui/language/english.ini

index=13

customini=./ui/language/CUSTOMER_04323_spanlish.ini

=======start scandir src=../www/HAPPLE/pages/ dst=/tmp/webcash/Español/

=======start scandir src=../www/HAPPLE/pages/sysTips/ dst=/tmp/webcash/Español/sysTips/

=======start scandir src=../www/HAPPLE/pages/sysTips/tipsImg/ dst=/tmp/webcash/Español/sysTips/tipsImg/

=======start scandir src=../www/HAPPLE/pages/proxy/ dst=/tmp/webcash/Español/proxy/

Cash include file ../www/HAPPLE/pages/proxy/../liveView.html to /tmp/webcash/Español/proxy/, filename=../liveView.html, fd=0x13d6d58

Cash include file ../www/HAPPLE/pages/proxy/../playback.html to /tmp/webcash/Español/proxy/, filename=../playback.html, fd=0x13d6d58

Cash include file ../www/HAPPLE/pages/proxy/../left.html to /tmp/webcash/Español/proxy/, filename=../left.html, fd=0x13d6d58

Cash include file ../www/HAPPLE/pages/liveView.html to /tmp/webcash/Español/, filename=liveView.html, fd=0x13d6d58

Cash include file ../www/HAPPLE/pages/playback.html to /tmp/webcash/Español/, filename=playback.html, fd=0x13d6d58

Cash include file ../www/HAPPLE/pages/left.html to /tmp/webcash/Español/, filename=left.html, fd=0x13d6d58

=======start scandir src=../www/HAPPLE/pages/images/ dst=/tmp/webcash/Español/images/

=======start scandir src=../www/HAPPLE/pages/WAP/ dst=/tmp/webcash/Español/WAP/

=======start scandir src=../www/HAPPLE/pages/Styles/ dst=/tmp/webcash/Español/Styles/

=======start scandir src=../www/HAPPLE/pages/LoadPage/ dst=/tmp/webcash/Español/LoadPage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemMessage/ dst=/tmp/webcash/Español/LoadPage/SystemMessage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemManagement/ dst=/tmp/webcash/Español/LoadPage/SystemManagement/

=======start scandir src=../www/HAPPLE/pages/LoadPage/NetworkService/ dst=/tmp/webcash/Español/LoadPage/NetworkService/

=======start scandir src=../www/HAPPLE/pages/LoadPage/EncodingSetting/ dst=/tmp/webcash/Español/LoadPage/EncodingSetting/

=======start scandir src=../www/HAPPLE/pages/LoadPage/AlarmSet/ dst=/tmp/webcash/Español/LoadPage/AlarmSet/

=======start scandir src=../www/HAPPLE/pages/JS/ dst=/tmp/webcash/Español/JS/



language Română is not select





language Ελληνικά is not select



Cash lan=Français ini=./ui/language/french.ini

Cash base english path=./ui/language/english.ini

index=13

customini=./ui/language/CUSTOMER_04323_french.ini

=======start scandir src=../www/HAPPLE/pages/ dst=/tmp/webcash/Français/

=======start scandir src=../www/HAPPLE/pages/sysTips/ dst=/tmp/webcash/Français/sysTips/

=======start scandir src=../www/HAPPLE/pages/sysTips/tipsImg/ dst=/tmp/webcash/Français/sysTips/tipsImg/

=======start scandir src=../www/HAPPLE/pages/proxy/ dst=/tmp/webcash/Français/proxy/

Cash include file ../www/HAPPLE/pages/proxy/../liveView.html to /tmp/webcash/Français/proxy/, filename=../liveView.html, fd=0x13cda28

Cash include file ../www/HAPPLE/pages/proxy/../playback.html to /tmp/webcash/Français/proxy/, filename=../playback.html, fd=0x13cda28

Cash include file ../www/HAPPLE/pages/proxy/../left.html to /tmp/webcash/Français/proxy/, filename=../left.html, fd=0x13cda28

Cash include file ../www/HAPPLE/pages/liveView.html to /tmp/webcash/Français/, filename=liveView.html, fd=0x13cda28

Cash include file ../www/HAPPLE/pages/playback.html to /tmp/webcash/Français/, filename=playback.html, fd=0x13cda28

Cash include file ../www/HAPPLE/pages/left.html to /tmp/webcash/Français/, filename=left.html, fd=0x13cda28

=======start scandir src=../www/HAPPLE/pages/images/ dst=/tmp/webcash/Français/images/

=======start scandir src=../www/HAPPLE/pages/WAP/ dst=/tmp/webcash/Français/WAP/

=======start scandir src=../www/HAPPLE/pages/Styles/ dst=/tmp/webcash/Français/Styles/

=======start scandir src=../www/HAPPLE/pages/LoadPage/ dst=/tmp/webcash/Français/LoadPage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemMessage/ dst=/tmp/webcash/Français/LoadPage/SystemMessage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemManagement/ dst=/tmp/webcash/Français/LoadPage/SystemManagement/

=======start scandir src=../www/HAPPLE/pages/LoadPage/NetworkService/ dst=/tmp/webcash/Français/LoadPage/NetworkService/

=======start scandir src=../www/HAPPLE/pages/LoadPage/EncodingSetting/ dst=/tmp/webcash/Français/LoadPage/EncodingSetting/

=======start scandir src=../www/HAPPLE/pages/LoadPage/AlarmSet/ dst=/tmp/webcash/Français/LoadPage/AlarmSet/

=======start scandir src=../www/HAPPLE/pages/JS/ dst=/tmp/webcash/Français/JS/

Cash lan=Русский ini=./ui/language/russian.ini

Cash base english path=./ui/language/english.ini

index=13

customini=./ui/language/CUSTOMER_04323_russian.ini

=======start scandir src=../www/HAPPLE/pages/ dst=/tmp/webcash/Русский/

=======start scandir src=../www/HAPPLE/pages/sysTips/ dst=/tmp/webcash/Русский/sysTips/

=======start scandir src=../www/HAPPLE/pages/sysTips/tipsImg/ dst=/tmp/webcash/Русский/sysTips/tipsImg/

=======start scandir src=../www/HAPPLE/pages/proxy/ dst=/tmp/webcash/Русский/proxy/

Cash include file ../www/HAPPLE/pages/proxy/../liveView.html to /tmp/webcash/Русский/proxy/, filename=../liveView.html, fd=0x13e1a60

Cash include file ../www/HAPPLE/pages/proxy/../playback.html to /tmp/webcash/Русский/proxy/, filename=../playback.html, fd=0x13e1a60

Cash include file ../www/HAPPLE/pages/proxy/../left.html to /tmp/webcash/Русский/proxy/, filename=../left.html, fd=0x13e1a60

Cash include file ../www/HAPPLE/pages/liveView.html to /tmp/webcash/Русский/, filename=liveView.html, fd=0x13e19e8

Cash include file ../www/HAPPLE/pages/playback.html to /tmp/webcash/Русский/, filename=playback.html, fd=0x13e19e8

Cash include file ../www/HAPPLE/pages/left.html to /tmp/webcash/Русский/, filename=left.html, fd=0x13e19e8

=======start scandir src=../www/HAPPLE/pages/images/ dst=/tmp/webcash/Русский/images/

=======start scandir src=../www/HAPPLE/pages/WAP/ dst=/tmp/webcash/Русский/WAP/

=======start scandir src=../www/HAPPLE/pages/Styles/ dst=/tmp/webcash/Русский/Styles/

=======start scandir src=../www/HAPPLE/pages/LoadPage/ dst=/tmp/webcash/Русский/LoadPage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemMessage/ dst=/tmp/webcash/Русский/LoadPage/SystemMessage/

=======start scandir src=../www/HAPPLE/pages/LoadPage/SystemManagement/ dst=/tmp/webcash/Русский/LoadPage/SystemManagement/

=======start scandir src=../www/HAPPLE/pages/LoadPage/NetworkService/ dst=/tmp/webcash/Русский/LoadPage/NetworkService/

=======start scandir src=../www/HAPPLE/pages/LoadPage/EncodingSetting/ dst=/tmp/webcash/Русский/LoadPage/EncodingSetting/

=======start scandir src=../www/HAPPLE/pages/LoadPage/AlarmSet/ dst=/tmp/webcash/Русский/LoadPage/AlarmSet/

=======start scandir src=../www/HAPPLE/pages/JS/ dst=/tmp/webcash/Русский/JS/



language Nederlands is not select





language עברית is not select





language 中文繁体 is not select





language Polski is not select



Free CCashLanguage

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.602]terminate Process name=/usr/local/bin/StreamGui



killall: /usr/local/bin/StreamGui: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.608]exit child: pid: 740 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.608]terminate Process name=/usr/local/bin/DeviceManage



killall: /usr/local/bin/DeviceManage: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.613]exit child: pid: 741 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.613]terminate Process name=/usr/local/bin/avStreaming



killall: /usr/local/bin/avStreaming: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.618]exit child: pid: 742 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.618]terminate Process name=/usr/local/bin/EventManage



killall: /usr/local/bin/EventManage: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.622]exit child: pid: 743 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.623]terminate Process name=/usr/local/bin/Storage



killall: /usr/local/bin/Storage: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.627]exit child: pid: 744 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.627]terminate Process name=/usr/local/bin/StreamingProtocol



killall: /usr/local/bin/StreamingProtocol: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.632]exit child: pid: 745 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.632]terminate Process name=/usr/local/bin/NetworkService



killall: /usr/local/bin/NetworkService: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.637]exit child: pid: 746 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.637]terminate Process name=/usr/local/bin/httpd



killall: /usr/local/bin/httpd: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.642]exit child: pid: 747 status: 256

[CenterServer:SoftWatchdog.cpp:TerminateProcess:98:Time:5.642]terminate Process name=/usr/local/bin/NATStreamingProtocol



killall: /usr/local/bin/NATStreamingProtocol: no process killed

[CenterServer:SoftWatchdog.cpp:OnSignalSIGCHLD:31:Time:5.647]exit child: pid: 748 status: 256

[CenterServer:watchdog.cpp:create:26:Time:5.695]Version:RMCBB Hisi Watchdog 1.0.0 RC1

DeviceManage Version[HI3520A]:2013-10-15 03:53:39

[GetSystemCfgJson-GetFileSize] len 40, {

    "DataLen":12978,

    "DataCrc":44

}

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000031]CDeviceManage::Dm_parse_system_config device type:7204XQ_VA 24

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000040]CDeviceManage::Dm_parse_system_config max hdd number:1

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000059]CDeviceManage::Dm_parse_system_config panel type:C1

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000071]CDeviceManage::Dm_parse_system_config P Hdelay 3

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000077]CDeviceManage::Dm_parse_system_config P hactive 0

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000083]CDeviceManage::Dm_parse_system_config P Vdelay 0

[DeviceManageSystemConfig.cpDriverHi35xxGpio Version[HI3520A]:2013-09-06 00:40:02

p][Dm_parse_system_config: 00000089]CDeviceManage::Dm_parse_system_config P vactive 0

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000095]CDeviceManage::Dm_parse_system_config N Hdelay 7

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000101]CDeviceManage::Dm_parse_system_config N hactive 0

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000107]CDeviceManage::Dm_parse_system_config N Vdelay 0

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000113]CDeviceManage::Dm_parse_system_config N vactive 0

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000122]CDeviceManage::Dm_parse_system_config APP TYPE:formal

[GetUartProtocalInfo:667]UARTPROTOCAL_LIST is not arrry[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000161]CDeviceManage::Dm_parse_system_config pSystem_config_parser->GetUartProtocalInfo FAILED

[DeviceManageSysDriverGpioI2c Version[HI3520A]:2013-09-06 00:40:19

temConfig.cpp][DGpioi2c_init config(bus_num:1):

m_parse_system_c        Gpio i2c bus(0):[SCL:GPIO13_3][SDA:GPIO13_2]

onfig: 00000187]CDeviceManage::Dm_parse_system_config alarm input num 4

[DeviceManageSystemConfig.cpp][Dm_parse_system_config: 00000193]CDeviceManage::Dm_parse_system_config alarm output num 1

[DeviceManageSystemConfig.cpp][Dm_init_main_board_ver: 00002103]Main board Version: 0DriverCx2682x Version[HI3520A]:2013-10-10 01:33:21(chip_num:1)

x0

[main.cpp][Signal_handle: 00Cx2682x_module_init (dev_addr:0x88)(rev_id:0xffff)

000018]Signal_haKernel panic - not syncing: Fail to realize chip id 0xFFFF



ndle Children PrBacktrace: ocess Exit: 1077

172260

[DeviceG[<c002e8d4>] (dump_backtrace+0x0/0x110) from [<c028d068>] (dump_stack+0x18/0x1c)

pioI2c.cpp][Gpio r6:bf9e6898i2c_init: 000001 r5:0000000062]pCmd_line ins r4:c0376ef0mod /module/extd r3:c03601d4rv/DriverGpioI2c

.ko gpioi2c_bus_[<c028d050>] (dump_stack+0x0/0x1c) from [<c028d0c8>] (panic+0x5c/0x17c)

num=1 gpioi2c_sc[<c028d06c>] (panic+0x0/0x17c) from [<bf9ea1cc>] (Cx2682x_module_init+0x1cc/0x398 [DriverCx2682x])

l1_group=13 gpio r3:00006824i2c_scl1_bit=3 g r2:c03601f0pioi2c_sda1_grou r1:0000ffffp=13 gpioi2c_sda r0:bf9e63d81_bit=2

[main.c

pp][Signal_handl r7:00000000e: 00000018]Sign

al_handle Childr[<bf9ea000>] (Cx2682x_module_init+0x0/0x398 [DriverCx2682x]) from [<c00253b4>] (do_one_initcall+0xa0/0x170)

en Process Exit: r6:00000000 1077179896

[De r5:bf9ea000viceManage.cpp][ r4:bf9e6938Dm_init: 0000390

4]CDeviceManage:[<c0025314>] (do_one_initcall+0x0/0x170) from [<c00639a8>] (sys_init_module+0x7c/0x198)

:Dm_init NOT SUP r9:c4e64000PORT HARDWARE I2 r8:c002b1c8C

[DeviceManage r7:00011a7c.cpp][Dm_init: 0 r6:000000000003915]CDeviceM r5:00851060anage::Dm_init N

r4:bf9e6938OT SUPPORT At88s

c0104

[<c006392c>] (sys_init_module+0x0/0x198) from [<c002b020>] (ret_fast_syscall+0x0/0x30)

 r7:00000080 r6:be9e2d44 r5:00000069 r4:be9e29d4

Аватара пользователя
VirtualLink
Специалист
Сообщения: 1846
Зарегистрирован: 09 апр 2016, 12:38

Re: gtr-04h(v.2) восстановление прошивки

Сообщение VirtualLink » 01 фев 2018, 13:25

Интересная зверушка!
Прежде всего через команды интерфейса sf скачай дамп, если даст и укажи файл с прошивкой, чем обновлял!
Твоё устройство поддерживает восстановление по usb (по логу загрузки), поэтому есть шанс восстановить так!
Дай команду printenv!

Limonchik
Новичок
Сообщения: 11
Зарегистрирован: 06 ноя 2017, 09:40

Re: gtr-04h(v.2) восстановление прошивки

Сообщение Limonchik » 02 фев 2018, 14:51

Код: Выделить всё

Streaming3520A #  printenv

bootargs=mem=92M console=ttyAMA0,115200 UartConfig=1 EtherConfig=1 root=/dev/mtdblock2 rootfstype=squashfs mtdparts=hi_sfc:640K(boot+3Logo),1792K(Kernel),13M(Root+App),64K(SysConfig),64K(SysStatus),512K(SysPara)

bootcmd=sf probe 0;sf read 0x82000000 0xA0000 0x1C0000;bootm 0x82000000

bootdelay=1

baudrate=115200

ethaddr=00:09:24:********

ipaddr=192.168.2.234

serverip=192.168.2.56

netmask=255.255.254.0

bootfile="uImage"

stdin=serial

stdout=serial

stderr=serial

verify=n

ver=U-Boot 2010.06 (Sep 24 2013 - 20:39:26)



Environment size: 515/262140 bytes

Streaming3520A #

попробовал сохранить дамп опираясь на эту статью https://docs.google.com/document/d/1rRN ... edit?pli=1" onclick="window.open(this.href);return false;
получилось только кернел, дальше видимо нужно как то считать с каких адресов считывать, а я не понимаю как это делается.
вот лог

Код: Выделить всё

Streaming3520A # sf probe 0

16384 KiB hi_sfc at 0:0 is now current device

Streaming3520A # sf read 0x82000000 0xA0000 0x1C0000



Streaming3520A # tftp 0x82000000 kernel.img 0x1C0000

MAC:   00-09-24******

TFTP to server 192.168.2.56; our IP address is 192.168.2.234

Upload Filename 'kernel.img'.

Upload from address: 0x82000000, 1.768 MB to be send ...

Uploading: #    [ Connected ]

################################        [ 1.000 MB]

########################

         1.768 MB upload ok.

Streaming3520A #

вот прошивка которую я ставил https://cloud.mail.ru/public/5CsH/pXVUozNys" onclick="window.open(this.href);return false;
вот та которая скорее всего стояла на регистраторе, она же самая свежая https://cloud.mail.ru/public/6A7H/6m5HGEMQk" onclick="window.open(this.href);return false;

да, я тоже заметил что он пытается грузится с usb, но похоже он не видит мою 16гб флешку (пишу и вспоминаю что и когда он был живой он не находил файл для обновления, прошивал по локалке) или файлы на ней, я уж как только не извращался, делал папку upgrade и dvr upgrade, ложил туда и в корень прошивку, переименовывал прошивку. нихотит оживать. надо будет попрбовать флешку меньшего размера, нет под рукой

Аватара пользователя
VirtualLink
Специалист
Сообщения: 1846
Зарегистрирован: 09 апр 2016, 12:38

Re: gtr-04h(v.2) восстановление прошивки

Сообщение VirtualLink » 02 фев 2018, 15:26

Limonchik писал(а): попробовал сохранить дамп опираясь на эту статью https://docs.google.com/document/d/1rRN ... edit?pli=1" onclick="window.open(this.href);return false;
получилось только кернел, дальше видимо нужно как то считать с каких адресов считывать, а я не понимаю как это делается.
вот лог

Код: Выделить всё

Streaming3520A # sf probe 0
16384 KiB hi_sfc at 0:0 is now current device
Streaming3520A # sf read 0x82000000 0xA0000 0x1C0000
Streaming3520A # tftp 0x82000000 kernel.img 0x1C0000
MAC:   00-09-24******
TFTP to server 192.168.2.56; our IP address is 192.168.2.234
Upload Filename 'kernel.img'.
Upload from address: 0x82000000, 1.768 MB to be send ...
Uploading: #    [ Connected ]
################################        [ 1.000 MB]
########################
         1.768 MB upload ok.
Streaming3520A #
Так у тебя все есть же в твоём логе!

Сделай так и получишь дамп!

Код: Выделить всё

sf probe 0
sf read 0x82000000 0x 0x1000000
tftp 0x82000000 flash.dat 0x1000000
Этот дамп и выложи глянуть!

Для прошивки с USB возможно потребуется специальный восстановительный файл, а флешка скорее всего да 2Гб в формате FAT32, хотя надо искать, что там у AVTECH!

Limonchik
Новичок
Сообщения: 11
Зарегистрирован: 06 ноя 2017, 09:40

Re: gtr-04h(v.2) восстановление прошивки

Сообщение Limonchik » 02 фев 2018, 18:22

другую флешку увидел, вот кусок лога

Код: Выделить всё

[UsbDeviceInit, 156]:Get Valid Partition on USB 0:4



Interface:  USB

  Device 0: Vendor: ADATA    Rev: 0.00 Prod: USB Flash Drive

            Type: Removable Hard Disk

            Capacity: 7415.0 MB = 7.2 GB (15185920 x 512)

Filesystem: FAT32 "NO NAME    "
[USBSoftwareUpgrade, 324]:FilenamesGet ▒у▒▒у▒
[USBSoftwareUpgrade, 325]:FilesizesGet
[USBSoftwareUpgrade, 329]:GetUpgradeFileName: Cann't Extract File Names From Folder
[USBSoftwareUpgrade, 662]:Come Over -1
[UpgradeSoftware, 1719]:USBSoftwareUpgrade: No Upgrade
[UpgradeSoftware, 1728]:Free Flash
файлы прошивки с оригинальным названием и названием upgrade, dvrupgrade не подхватывает.
Так у тебя все есть же в твоём логе!
:smile: для меня это куча непонятного текста
Этот дамп и выложи глянуть!
https://cloud.mail.ru/public/BRws/YFpoVYc81" onclick="window.open(this.href);return false;
в принципе если это сильно упростит восстановление, то могу попытаться снять дамп с точно такого же регистратора, но рабочего.

Аватара пользователя
VirtualLink
Специалист
Сообщения: 1846
Зарегистрирован: 09 апр 2016, 12:38

Re: gtr-04h(v.2) восстановление прошивки

Сообщение VirtualLink » 02 фев 2018, 18:53

Дамп можно убирать из доступа, но не потерять!
По имени надо поглядеть и почитать!

Limonchik
Новичок
Сообщения: 11
Зарегистрирован: 06 ноя 2017, 09:40

Re: gtr-04h(v.2) восстановление прошивки

Сообщение Limonchik » 06 фев 2018, 08:01

все выходные провёл в инете в поисках решения моего вопроса, безрезультатно.
сегодня дай думаю ещё попробую поколдовать с флешкой, и в консоли побежали сточки

Код: Выделить всё

Interface:  USB

  Device 0: Vendor: ADATA    Rev: 0.00 Prod: USB Flash Drive

            Type: Removable Hard Disk

            Capacity: 7415.0 MB = 7.2 GB (15185920 x 512)

Filesystem: FAT32 "NO NAME    "

            ./

            ../

 12142431   rm7204xq_va_dvr_t2014092440-c1-04.323-ui1



1 file(s), 2 dir(s)



[USBSoftwareUpgrade, 324]:FilenamesGet rm7204xq_va_dvr_t2014092440-c1-04.323-ui1;



[USBSoftwareUpgrade, 325]:FilesizesGet 12142431;



[GetUpgradeFileName, 218]:FileNamesAll rm7204xq_va_dvr_t2014092440-c1-04.323-ui1;



[GetUpgradeFileName, 251]:FileNamesAll  UpgradeFileFullName dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.32               3-ui1



[GetUpgradeFileName, 256]:File dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 Size 12142431



[USBSoftwareUpgrade, 368]:Current File dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 Size 12142431



reading dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 at 0 for 1024

[Upgrade_is_my_software_packet_header, 221]: Upgrade_is_my_software_packet_header entry_num:7, 80

[Upgrade_is_my_software_packet_header, 225]:id 0x8A version T092440



[Upgrade_is_my_software_packet_header, 225]:id 0x89 version T20140924_40



[USBSoftwareUpgrade, 392]:Get Valid Packet dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 size 121424               31



[USBSoftwareUpgrade, 349]:Finish Loop Files



[USBSoftwareUpgrade, 536]:Read dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 For Upgrade_start_upgra               de



reading dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 at 0 for 1024

[Upgrade_is_my_software_packet_header, 221]: Upgrade_is_my_software_packet_header entry_num:7, 80

[Upgrade_is_my_software_packet_header, 225]:id 0x8A version T092440



[Upgrade_is_my_software_packet_header, 225]:id 0x89 version T20140924_40



[Upgrade_start_upgrade, 662]: Upgrade_start_upgrade OK!!!!!!!!!!!!!!!

[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



[HAL_LAYER_EnableLayer, 3205]:pVoReg->G0CTRL.u32 0x205C9000



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



graphic layer 0 closed!

dev 0 closed!

16384 KiB hi_sfc at 0:0 is now current device



dev 0 set background color!

jpeg decoding ...

<<addr=0x83000000, size=0x20000, vobuf=0x83200000>>

mmu_enable

<<imgwidth=720, imgheight=576, linebytes=1440>>

decode success!!!!

decode jpeg!

[ResizeBuf, 13]:Start Copy Upgrade from 0x83200000 to 0x83600000



[ResizeBuf, 20]:End Copy Upgrade

я уже обрадовался, но рано, на этом регистратор застыл, ждал минут 10, тишина. вытащил флешку и перезагрузил по питанию. как и раньше появлялась заставка и регистратор перезагружался. в расстройстве дай думаю ещё раз ему флешку воткну и тут вижу

Код: Выделить всё

************************************************

U_BOOT:7204XQ_VA UBOOT  T20130924 20:39:19

************************************************

main_board_ver 0

DRAM:  256 MiB

Check spi flash controller v300. found

Spi(cs1) ID: 0x01 0x20 0x18 0x4D 0x01 0x80

Get match S25FL129P1/S25FL128S 0x1C 0x0

Spi(cs1): Block:64KB Chip:16MB Name:"S25FL127S1"

*** Warning - bad CRC, using default environment



In:    serial

Out:   serial

Err:   serial

judge ddr init

user init finish.

Hit CTRL + C to stop autoboot:  0

16384 KiB hi_sfc at 0:0 is now current device



[MachineTypeCheck, 1692]:DeviceType 24



[UpgradeSoftware, 1709]:Check Upgrade At Momory Address 0x00000000



[VerifyMmpValid, 229]:Bad memory Addr 0x00000000



[CommonUpgrade, 1230]:Invalid Upgrade Addr 0x00000000



USB:   scanning bus for devices... 2 USB Device(s) found

1 Storage Device(s) found

Unable to use USB 0:0 for fatls

** Partition 1 not valid on device 0 **

Unable to use USB 0:1 for fatls

** Partition 2 not valid on device 0 **

Unable to use USB 0:2 for fatls

** Partition 3 not valid on device 0 **

Unable to use USB 0:3 for fatls

[UsbDeviceInit, 156]:Get Valid Partition on USB 0:4



Interface:  USB

  Device 0: Vendor: ADATA    Rev: 0.00 Prod: USB Flash Drive

            Type: Removable Hard Disk

            Capacity: 7415.0 MB = 7.2 GB (15185920 x 512)

Filesystem: FAT32 "NO NAME    "

            ./

            ../

 12142431   rm7204xq_va_dvr_t2014092440-c1-04.323-ui1



1 file(s), 2 dir(s)



[USBSoftwareUpgrade, 324]:FilenamesGet rm7204xq_va_dvr_t2014092440-c1-04.323-ui1;



[USBSoftwareUpgrade, 325]:FilesizesGet 12142431;



[GetUpgradeFileName, 218]:FileNamesAll rm7204xq_va_dvr_t2014092440-c1-04.323-ui1;



[GetUpgradeFileName, 251]:FileNamesAll  UpgradeFileFullName dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1



[GetUpgradeFileName, 256]:File dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 Size 12142431



[USBSoftwareUpgrade, 368]:Current File dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 Size 12142431



reading dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 at 0 for 1024

[Upgrade_is_my_software_packet_header, 221]: Upgrade_is_my_software_packet_header entry_num:7, 80

[Upgrade_is_my_software_packet_header, 225]:id 0x8A version T092440



[Upgrade_is_my_software_packet_header, 225]:id 0x89 version T20140924_40



[USBSoftwareUpgrade, 392]:Get Valid Packet dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 size 12142431



[USBSoftwareUpgrade, 349]:Finish Loop Files



[USBSoftwareUpgrade, 536]:Read dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 For Upgrade_start_upgrade



reading dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 at 0 for 1024

[Upgrade_is_my_software_packet_header, 221]: Upgrade_is_my_software_packet_header entry_num:7, 80

[Upgrade_is_my_software_packet_header, 225]:id 0x8A version T092440



[Upgrade_is_my_software_packet_header, 225]:id 0x89 version T20140924_40



[Upgrade_start_upgrade, 662]: Upgrade_start_upgrade OK!!!!!!!!!!!!!!!

[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



[HAL_LAYER_EnableLayer, 3205]:pVoReg->G0CTRL.u32 0x205C9000



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



graphic layer 0 closed!

dev 0 closed!

16384 KiB hi_sfc at 0:0 is now current device



dev 0 set background color!

jpeg decoding ...

<<addr=0x83000000, size=0x20000, vobuf=0x83200000>>

mmu_enable

<<imgwidth=720, imgheight=576, linebytes=1440>>

decode success!!!!

decode jpeg!

[ResizeBuf, 13]:Start Copy Upgrade from 0x83200000 to 0x83600000



[ResizeBuf, 20]:End Copy Upgrade



dev 0 opened!

[HAL_LAYER_EnableLayer, 3205]:pVoReg->G0CTRL.u32 0x205C9000



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



graphic layer 0 opened!

dev 2 opened!

[HAL_LAYER_EnableLayer, 3205]:pVoReg->G0CTRL.u32 0x205C9000



[HAL_LAYER_SetRegUp, 5215]:pVoReg->G0UPD.u32 0x205C9004



graphic layer 2 opened!

[USBSoftwareUpgrade, 627]:Read Packet dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 size 12142431



reading dvrupgrade/rm7204xq_va_dvr_t2014092440-c1-04.323-ui1 at 0 for 12142431

....................................................................................................................
....................................................................................................................
....................................................................................................................
....................................................................................................................
...................................................................................................................
....................................................................................................................
....................................................................................................................
....................................................................................................................
....................................................................................................................
....................................................................................................................
..........................

Upgrade_put_data info:

    is_logo_config_file:false

    id:00000000

    len:12142431

    gUpgrade_file_offset:00000000

[VerifyMmpValid, 270]:index 0 id 0x8A len 23619



[VerifyMmpValid, 270]:index 1 id 0x89 len 10457088



[VerifyMmpValid, 270]:index 2 id 0x88 len 1341280



[VerifyMmpValid, 270]:index 3 id 0x87 len 250324



[VerifyMmpValid, 270]:index 4 id 0x1 len 24872



[VerifyMmpValid, 270]:index 5 id 0x2 len 32125



[VerifyMmpValid, 270]:index 6 id 0x3 len 12475



[CommonUpgrade, 1268]:Unlock SPI for Upgrade



unLock All Flash

[CommonUpgrade, 1367]:StartAddr 0xF60000 EndAddr 0x10000 len 23619



[CommonUpgrade, 1377]:id 0x8A version T092440 Start 0xF60000 End 0x10000 uboot 0




Erasing at 0xf70000 -- 100% complete.


Writing at 0xf65c43 -- 100% complete.

[CommonUpgrade, 1512]:Write to [0x00F60000: 0x00010000] Success



[CommonUpgrade, 1367]:StartAddr 0x260000 EndAddr 0xD00000 len 10457088



[CommonUpgrade, 1377]:id 0x89 version T20140924_40 Start 0x260000 End 0xD00000 uboot 0




Erasing at 0x270000 --   0% complete.
Erasing at 0x290000 --   1% complete.
Erasing at 0x2b0000 --   2% complete.
Erasing at 0x2d0000 --   3% complete.
Erasing at 0x2f0000 --   4% complete.
Erasing at 0x310000 --   5% complete.
Erasing at 0x330000 --   6% complete.
Erasing at 0x350000 --   7% complete.
Erasing at 0x370000 --   8% complete.
Erasing at 0x390000 --   9% complete.
Erasing at 0x3b0000 --  10% complete.
Erasing at 0x3d0000 --  11% complete.
Erasing at 0x3f0000 --  12% complete.
Erasing at 0x420000 --  13% complete.
Erasing at 0x440000 --  14% complete.
Erasing at 0x460000 --  15% complete.
Erasing at 0x480000 --  16% complete.
Erasing at 0x4a0000 --  17% complete.
Erasing at 0x4c0000 --  18% complete.
Erasing at 0x4e0000 --  19% complete.
Erasing at 0x500000 --  20% complete.
Erasing at 0x520000 --  21% complete.
Erasing at 0x540000 --  22% complete.
Erasing at 0x560000 --  23% complete.
Erasing at 0x580000 --  24% complete.
Erasing at 0x5a0000 --  25% complete.
Erasing at 0x5d0000 --  26% complete.
Erasing at 0x5f0000 --  27% complete.
Erasing at 0x610000 --  28% complete.
Erasing at 0x630000 --  29% complete.
Erasing at 0x650000 --  30% complete.
Erasing at 0x670000 --  31% complete.
Erasing at 0x690000 --  32% complete.
Erasing at 0x6b0000 --  33% complete.
Erasing at 0x6d0000 --  34% complete.
Erasing at 0x6f0000 --  35% complete.
Erasing at 0x710000 --  36% complete.
Erasing at 0x730000 --  37% complete.
Erasing at 0x760000 --  38% complete.
Erasing at 0x780000 --  39% complete.
Erasing at 0x7a0000 --  40% complete.
Erasing at 0x7c0000 --  41% complete.
Erasing at 0x7e0000 --  42% complete.
Erasing at 0x800000 --  43% complete.
Erasing at 0x820000 --  44% complete.
Erasing at 0x840000 --  45% complete.
Erasing at 0x860000 --  46% complete.
Erasing at 0x880000 --  47% complete.
Erasing at 0x8a0000 --  48% complete.
Erasing at 0x8c0000 --  49% complete.
Erasing at 0x8e0000 --  50% complete.
Erasing at 0x910000 --  51% complete.
Erasing at 0x930000 --  52% complete.
Erasing at 0x950000 --  53% complete.
Erasing at 0x970000 --  54% complete.
Erasing at 0x990000 --  55% complete.
Erasing at 0x9b0000 --  56% complete.
Erasing at 0x9d0000 --  57% complete.
Erasing at 0x9f0000 --  58% complete.
Erasing at 0xa10000 --  59% complete.
Erasing at 0xa30000 --  60% complete.
Erasing at 0xa50000 --  61% complete.
Erasing at 0xa70000 --  62% complete.
Erasing at 0xaa0000 --  63% complete.
Erasing at 0xac0000 --  64% complete.
Erasing at 0xae0000 --  65% complete.
Erasing at 0xb00000 --  66% complete.
Erasing at 0xb20000 --  67% complete.
Erasing at 0xb40000 --  68% complete.
Erasing at 0xb60000 --  69% complete.
Erasing at 0xb80000 --  70% complete.
Erasing at 0xba0000 --  71% complete.
Erasing at 0xbc0000 --  72% complete.
Erasing at 0xbe0000 --  73% complete.
Erasing at 0xc00000 --  74% complete.
Erasing at 0xc20000 --  75% complete.
Erasing at 0xc50000 --  76% complete.
Erasing at 0xc70000 --  77% complete.
Erasing at 0xc90000 --  78% complete.
Erasing at 0xcb0000 --  79% complete.
Erasing at 0xcd0000 --  80% complete.
Erasing at 0xcf0000 --  81% complete.
Erasing at 0xd10000 --  82% complete.
Erasing at 0xd30000 --  83% complete.
Erasing at 0xd50000 --  84% complete.
Erasing at 0xd70000 --  85% complete.
Erasing at 0xd90000 --  86% complete.
Erasing at 0xdb0000 --  87% complete.
Erasing at 0xde0000 --  88% complete.
Erasing at 0xe00000 --  89% complete.
Erasing at 0xe20000 --  90% complete.
Erasing at 0xe40000 --  91% complete.
Erasing at 0xe60000 --  92% complete.
Erasing at 0xe80000 --  93% complete.
Erasing at 0xea0000 --  94% complete.
Erasing at 0xec0000 --  95% complete.
Erasing at 0xee0000 --  96% complete.
Erasing at 0xf00000 --  97% complete.
Erasing at 0xf20000 --  98% complete.
Erasing at 0xf40000 --  99% complete.
Erasing at 0xf60000 -- 100% complete.


Writing at 0x270000 --   0% complete.
Writing at 0x280000 --   1% complete.
Writing at 0x2a0000 --   2% complete.
Writing at 0x2b0000 --   3% complete.
Writing at 0x2d0000 --   4% complete.
Writing at 0x2e0000 --   5% complete.
Writing at 0x300000 --   6% complete.
Writing at 0x320000 --   7% complete.
Writing at 0x330000 --   8% complete.
Writing at 0x350000 --   9% complete.
Writing at 0x360000 --  10% complete.
Writing at 0x380000 --  11% complete.
Writing at 0x3a0000 --  12% complete.
Writing at 0x3b0000 --  13% complete.
Writing at 0x3d0000 --  14% complete.
Writing at 0x3e0000 --  15% complete.
Writing at 0x400000 --  16% complete.
Writing at 0x420000 --  17% complete.
Writing at 0x430000 --  18% complete.
Writing at 0x450000 --  19% complete.
Writing at 0x460000 --  20% complete.
Writing at 0x480000 --  21% complete.
Writing at 0x4a0000 --  22% complete.
Writing at 0x4b0000 --  23% complete.
Writing at 0x4d0000 --  24% complete.
Writing at 0x4e0000 --  25% complete.
Writing at 0x500000 --  26% complete.
Writing at 0x520000 --  27% complete.
Writing at 0x530000 --  28% complete.
Writing at 0x550000 --  29% complete.
Writing at 0x560000 --  30% complete.
Writing at 0x580000 --  31% complete.
Writing at 0x5a0000 --  32% complete.
Writing at 0x5b0000 --  33% complete.
Writing at 0x5d0000 --  34% complete.
Writing at 0x5e0000 --  35% complete.
Writing at 0x600000 --  36% complete.
Writing at 0x620000 --  37% complete.
Writing at 0x630000 --  38% complete.
Writing at 0x650000 --  39% complete.
Writing at 0x660000 --  40% complete.
Writing at 0x680000 --  41% complete.
Writing at 0x6a0000 --  42% complete.
Writing at 0x6b0000 --  43% complete.
Writing at 0x6d0000 --  44% complete.
Writing at 0x6e0000 --  45% complete.
Writing at 0x700000 --  46% complete.
Writing at 0x710000 --  47% complete.
Writing at 0x730000 --  48% complete.
Writing at 0x750000 --  49% complete.
Writing at 0x760000 --  50% complete.
Writing at 0x780000 --  51% complete.
Writing at 0x790000 --  52% complete.
Writing at 0x7b0000 --  53% complete.
Writing at 0x7d0000 --  54% complete.
Writing at 0x7e0000 --  55% complete.
Writing at 0x800000 --  56% complete.
Writing at 0x810000 --  57% complete.
Writing at 0x830000 --  58% complete.
Writing at 0x850000 --  59% complete.
Writing at 0x860000 --  60% complete.
Writing at 0x880000 --  61% complete.
Writing at 0x890000 --  62% complete.
Writing at 0x8b0000 --  63% complete.
Writing at 0x8d0000 --  64% complete.
Writing at 0x8e0000 --  65% complete.
Writing at 0x900000 --  66% complete.
Writing at 0x910000 --  67% complete.
Writing at 0x930000 --  68% complete.
Writing at 0x950000 --  69% complete.
Writing at 0x960000 --  70% complete.
Writing at 0x980000 --  71% complete.
Writing at 0x990000 --  72% complete.
Writing at 0x9b0000 --  73% complete.
Writing at 0x9d0000 --  74% complete.
Writing at 0x9e0000 --  75% complete.
Writing at 0xa00000 --  76% complete.
Writing at 0xa10000 --  77% complete.
Writing at 0xa30000 --  78% complete.
Writing at 0xa50000 --  79% complete.
Writing at 0xa60000 --  80% complete.
Writing at 0xa80000 --  81% complete.
Writing at 0xa90000 --  82% complete.
Writing at 0xab0000 --  83% complete.
Writing at 0xad0000 --  84% complete.
Writing at 0xae0000 --  85% complete.
Writing at 0xb00000 --  86% complete.
Writing at 0xb10000 --  87% complete.
Writing at 0xb30000 --  88% complete.
Writing at 0xb50000 --  89% complete.
Writing at 0xb60000 --  90% complete.
Writing at 0xb80000 --  91% complete.
Writing at 0xb90000 --  92% complete.
Writing at 0xbb0000 --  93% complete.
Writing at 0xbc0000 --  94% complete.
Writing at 0xbe0000 --  95% complete.
Writing at 0xc00000 --  96% complete.
Writing at 0xc10000 --  97% complete.
Writing at 0xc30000 --  98% complete.
Writing at 0xc40000 --  99% complete.
Writing at 0xc59000 -- 100% complete.

[CommonUpgrade, 1512]:Write to [0x00260000: 0x00D00000] Success



[CommonUpgrade, 1367]:StartAddr 0xA0000 EndAddr 0x1C0000 len 1341280



[CommonUpgrade, 1377]:id 0x88 version T062000 Start 0xA0000 End 0x1C0000 uboot 0




Erasing at 0xb0000 --   3% complete.
Erasing at 0xc0000 --   7% complete.
Erasing at 0xd0000 --  10% complete.
Erasing at 0xe0000 --  14% complete.
Erasing at 0xf0000 --  17% complete.
Erasing at 0x100000 --  21% complete.
Erasing at 0x110000 --  25% complete.
Erasing at 0x120000 --  28% complete.
Erasing at 0x130000 --  32% complete.
Erasing at 0x140000 --  35% complete.
Erasing at 0x150000 --  39% complete.
Erasing at 0x160000 --  42% complete.
Erasing at 0x170000 --  46% complete.
Erasing at 0x180000 --  50% complete.
Erasing at 0x190000 --  53% complete.
Erasing at 0x1a0000 --  57% complete.
Erasing at 0x1b0000 --  60% complete.
Erasing at 0x1c0000 --  64% complete.
Erasing at 0x1d0000 --  67% complete.
Erasing at 0x1e0000 --  71% complete.
Erasing at 0x1f0000 --  75% complete.
Erasing at 0x200000 --  78% complete.
Erasing at 0x210000 --  82% complete.
Erasing at 0x220000 --  85% complete.
Erasing at 0x230000 --  89% complete.
Erasing at 0x240000 --  92% complete.
Erasing at 0x250000 --  96% complete.
Erasing at 0x260000 -- 100% complete.


Writing at 0xb0000 --   4% complete.
Writing at 0xc0000 --   9% complete.
Writing at 0xd0000 --  14% complete.
Writing at 0xe0000 --  19% complete.
Writing at 0xf0000 --  24% complete.
Writing at 0x100000 --  29% complete.
Writing at 0x110000 --  34% complete.
Writing at 0x120000 --  39% complete.
Writing at 0x130000 --  43% complete.
Writing at 0x140000 --  48% complete.
Writing at 0x150000 --  53% complete.
Writing at 0x160000 --  58% complete.
Writing at 0x170000 --  63% complete.
Writing at 0x180000 --  68% complete.
Writing at 0x190000 --  73% complete.
Writing at 0x1a0000 --  78% complete.
Writing at 0x1b0000 --  83% complete.
Writing at 0x1c0000 --  87% complete.
Writing at 0x1d0000 --  92% complete.
Writing at 0x1e0000 --  97% complete.
Writing at 0x1e7760 -- 100% complete.

[CommonUpgrade, 1512]:Write to [0x000A0000: 0x001C0000] Success



[CommonUpgrade, 1367]:StartAddr 0x0 EndAddr 0x60000 len 250324



[CommonUpgrade, 1377]:id 0x87 version T042998 Start 0x0 End 0x60000 uboot 1




Erasing at 0x10000 --  16% complete.
Erasing at 0x20000 --  33% complete.
Erasing at 0x30000 --  50% complete.
Erasing at 0x40000 --  66% complete.
Erasing at 0x50000 --  83% complete.
Erasing at 0x60000 -- 100% complete.


Writing at 0x10000 --  26% complete.
Writing at 0x20000 --  52% complete.
Writing at 0x30000 --  78% complete.
Writing at 0x3d1d4 -- 100% complete.

[CommonUpgrade, 1512]:Write to [0x00000000: 0x00060000] Success



[CommonUpgrade, 1367]:StartAddr 0x60000 EndAddr 0x20000 len 24872



[CommonUpgrade, 1377]:id 0x1 version T092440 Start 0x60000 End 0x20000 uboot 0




Erasing at 0x70000 --  50% complete.
Erasing at 0x80000 -- 100% complete.


Writing at 0x66128 -- 100% complete.

[CommonUpgrade, 1512]:Write to [0x00060000: 0x00020000] Success



[CommonUpgrade, 1367]:StartAddr 0x87000 EndAddr 0x19000 len 32125



[CommonUpgrade, 1377]:id 0x2 version T092440 Start 0x87000 End 0x19000 uboot 0



[EraseFlash, 981]:Backup From 0x00080000 Size 0x7000




Erasing at 0x90000 --  50% complete.
Erasing at 0xa0000 -- 100% complete.


Writing at 0x87000 -- 100% complete.

[EraseFlash, 1001]:Restore to 0x00080000 Size 0x7000




Writing at 0x8ed7d -- 100% complete.

[CommonUpgrade, 1512]:Write to [0x00087000: 0x00019000] Success



[CommonUpgrade, 1367]:StartAddr 0x80000 EndAddr 0x7000 len 12475



[CommonUpgrade, 1377]:id 0x3 version T092440 Start 0x80000 End 0x7000 uboot 0



[EraseFlash, 992]:Backup From 0x00087000 Size 0x9000




Erasing at 0x90000 -- 100% complete.


Writing at 0x90000 -- 100% complete.

[EraseFlash, 1006]:Restore to 0x00087000 Size 0x9000




Writing at 0x830bb -- 100% complete.

[CommonUpgrade, 1512]:Write to [0x00080000: 0x00007000] Success



[CommonUpgrade, 1531]:Erasing System Status...




Erasing at 0xf80000 -- 100% complete.

[CommonUpgrade, 1547]:Writing System Status [0x  f70000:0x     1ec]...


Writing at 0xf701ec -- 100% complete.

[CommonUpgrade, 1569]:Refresh System Status done



[CommonUpgrade, 1574]:Finish Upgrade lock SPI for Security



Lock All ▒

рег ожил. а офф поддержка, морозилась, говорили шли нам, специалисты разберутся. жмоты
всем спасибо, поеду ставить рег на место

antipetya
Новичок
Сообщения: 43
Зарегистрирован: 06 дек 2014, 11:40
Откуда: Сыктывкар

Re: gtr-04h(v.2) восстановление прошивки

Сообщение antipetya » 06 фев 2018, 10:31

Поздравляю!)

Аватара пользователя
VirtualLink
Специалист
Сообщения: 1846
Зарегистрирован: 09 апр 2016, 12:38

Re: gtr-04h(v.2) восстановление прошивки

Сообщение VirtualLink » 06 фев 2018, 18:57

!

dennee
Новичок
Сообщения: 1
Зарегистрирован: 30 апр 2018, 08:20

Re: gtr-04h(v.2) восстановление прошивки

Сообщение dennee » 30 апр 2018, 08:24

День добрый!
Такая же проблема. Подскажите, что Вы таки наколдовали с флешкой?

Ответить

Вернуться в «Аналоговые системы видеонаблюдения»