Neovizus NVD216a: помощь в восстановлении

[VirtualLink]

Надо понимать, что у тебя там такое вначале и лучше получить дамп так или иначе вначале всех экспериментов!
Так и не понятно что случилось, какие симптомы!
Это тоже самое что в аптеке попросить вот тех красивых таблеток!

[d37]

Здравствуйте! Помогите восстановить регистратор NVD216a плата DVR-616-2-2 V1.3. При включении один раз пищит и виснет на логотипе, через 4 минуты перезагружается.
UART пишет:
U-Boot 2008.10 (Jul 26 2011 - 21:22:58)

DRAM: 256 MB
## Unknown FLASH on Bank 2 - Size = 0x00000000 =
Flash: 16 MB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Press CTRL-C to abort autoboot in alpum_set!!
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
## Booting kernel from Legacy Image at 80080000 ...
Image Name:
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1448408 Bytes = 1.4 MB
Load Address: e2800000
Entry Point: e2800000
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................
............................... done, booting the kernel.
Linux version 2.6.24-rt1-hi3520v100 (root@ubuntu) (gcc version 3.4.3 (release) (
CodeSourcery ARM Q3cvs 2004)) #17 Wed May 16 05:20:33 PDT 2012
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387f
Machine: hi3520v100
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 18288
Kernel command line: mem=72M console=ttyAMA0,115200 root=1f01 rootfstype=cramfs
mtdparts=physmap-flash.0:5M(boot),6M(rootfs),3584k(oem),1536k(config) pcimod=hos
t pciclksel=1 mac=00:17:4f:01:31:99 VDOSYS=PAL DDR=1G NET=MII
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 72MB = 72MB total
Memory: 69900KB available (2636K code, 242K data, 100K init)
Mount-cache hash table entries: 512
HI_VERSION=LINUX_2_6_24-M01C04FB01F @Hi3520v100R001_C_0_2_0 2010-03-12 13:45:01
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
Hisilicon clock system V0.01
PCI: device 0000:00:00.0 has unknown header type 25, ignoring.
PCI: device 0000:00:01.0 has unknown header type 25, ignoring.
PCI: device 0000:00:03.0 has unknown header type 14, ignoring.
PCI: device 0000:00:04.0 has unknown header type 14, ignoring.
PCI: device 0000:00:05.0 has unknown header type 14, ignoring.
PCI: device 0000:00:06.0 has unknown header type 14, ignoring.
PCI: device 0000:00:07.0 has unknown header type 14, ignoring.
PCI: device 0000:00:08.0 has unknown header type 14, ignoring.
PCI: device 0000:00:09.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0a.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0b.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0c.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0d.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0e.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0f.0 has unknown header type 14, ignoring.
PCI: device 0000:00:10.0 has unknown header type 14, ignoring.
PCI: device 0000:00:11.0 has unknown header type 14, ignoring.
PCI: device 0000:00:12.0 has unknown header type 14, ignoring.
PCI: device 0000:00:13.0 has unknown header type 14, ignoring.
PCI: device 0000:00:14.0 has unknown header type 14, ignoring.
PCI: device 0000:00:15.0 has unknown header type 14, ignoring.
PCI: device 0000:00:16.0 has unknown header type 14, ignoring.
PCI: device 0000:00:17.0 has unknown header type 14, ignoring.
PCI: device 0000:00:18.0 has unknown header type 14, ignoring.
PCI: device 0000:00:19.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1a.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1b.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1c.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1d.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1e.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1f.0 has unknown header type 14, ignoring.
PCI: bus0: Fast back to back transfers disabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: hisi_timer1 clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) B) 2001-2006 Red Hat, Inc.
yaffs Mar 25 2010 07:44:11 Installing.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20090000 (irq = 12) is a AMBA/PL011
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x200a0000 (irq = 12) is a AMBA/PL011
uart:2: ttyAMA2 at MMIO 0x200b0000 (irq = 13) is a AMBA/PL011
RAMDISK driver initialized: 4 RAM disks of 16384K size 4096 blocksize
loop: module loaded
physmap platform flash device: 04000000 at 80000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
4 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x00500000 : "boot"
0x00500000-0x00b00000 : "rootfs"
0x00b00000-0x00e80000
0x00e80000-0x01000000 : "config"
No NAND device found!!!
h2v100-ehci h2v100-ehci.0: h2v100-ehci
h2v100-ehci h2v100-ehci.0: new USB bus registered, assigned bus number 1
h2v100-ehci h2v100-ehci.0: irq 23, io mem 0x100b0000
h2v100-ehci h2v100-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
h2v100-ohci h2v100-ohci.0: h2v100-ohci
h2v100-ohci h2v100-ohci.0: new USB bus registered, assigned bus number 2
h2v100-ohci h2v100-ohci.0: irq 22, io mem 0x100a0000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
u32 classifier
Performance counters on
Netfilter messages via NETLINK v0.30.
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 100K
init started: BusyBox v1.1.2 (2010.10.12-04:51+0000) multi-call binary

_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
[RCS]: /etc/init.d/S20Cfg
RESO=1280x1024
RESO_W=1280
RESO_H=1024
NTSC_PAL_SW=1
AUTO=0
VDOSYS=PAL
NORM=2
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110104: 0x00009876 --> 0x00009654
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110100: 0x00000888 --> 0x00000886
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011010c: 0x00000001 --> 0x00000002
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110110: 0x00000002 --> 0x00000006
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110114: 0x00000003 --> 0x00000007
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110118: 0x00000005 --> 0x00000006
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011011c: 0x00000006 --> 0x00000007
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110128: 0x00000007 --> 0x00010020
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011012c: 0x00000007 --> 0x000103A1
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110130: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110134: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110138: 0x00000007 --> 0x00000004
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011013c: 0x00000007 --> 0x00000004
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050078: 0x00000000 --> 0x00008002
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120100: 0x00000444 --> 0x00000444
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120104: 0x00009876 --> 0x00009654
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012010c: 0x00000001 --> 0x00010640
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120110: 0x00000002 --> 0x00000003
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120114: 0x00000003 --> 0x00000004
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120118: 0x00000005 -Hisilicon Media Memory Zone Manager
-> 0x00000001
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012011c: 0x00000006 --> 0x00000002
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120128: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012012c: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120130: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120134: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120138: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012013c: 0x00000007 --> 0x00000005
[ipcm_vdd_init, 422]: local_cpu_id = 36

[ipcm_vdd_close, 268]: handle 0xc47d7540

[ipcm_vdd_init, 455]: IPCM hardware initialized successfully 0

hifb: module license 'Proprietary' taints kernel.
hifb info: HIFB_MAIN_VERSION[v1.0.0.2] Build Time[Sep 29 2010,
hifb info: video:vram0_size=5242880,vram1_size=11538432,vram2_size=1658880,vram4
_size=4096
hifb info: succeed in registering the fb0: ovl0 frame buffer device
hifb info: succeed in registering the fb1: ovl1 frame buffer device
hifb info: succeed in registering the fb2: ovl2 frame buffer device
hifb info: succeed in registering the fb3: ovl4 frame buffer device
TDE_MAIN_VERSION[v2.0.0.0] Build Time[Sep 29 2010, 16:15:28]
TDE_ADP_VERSION[hi3520adp v2.0.0.0] Build Time[Sep 29 2010, 16:15:28]
tde run on master arm
tde run for graphic service
tde map reg:basePhyAddr:20140000 baseVirAddr:c5074000 size:3000
Hisilicon UMAP device driver interface: v3.00
Chip Version: Hi35200100
load vd.ko ....OK!
load simd.ko OK
load vdec.ko ....OK
load vpp.ko ....OK!
load md.ko....OK!
insmod: cannot open module `hi3520_pciv_fmwm.ko': No such file or directory
nvp1104a driver init successful! chips = 0, norm = 2,audio stage=0
chips:2, norm:2
chips:2, norm:2
chips:2, norm:2
rn6264: version magic '2.6.24-rt1-hi3515v100 mod_unload ARMv5 ' should b
4-rt1-hi3520v100 mod_unload ARMv6 '
insmod: cannot insert `/dvr/extdrv/rn6264.ko': Invalid module format (-1): Exec
format error
cat: /sys/module/rn6264/parameters/chips: No such file or directory
[: 0: unknown operand
VD=TW2868
VD_NORM=2
[ IPCM_Check, 222]: remote not ready, now connect and wait ...
[ IPCM_Check, 252]: remote connected
box_init[67]: pch=1280x1024
box_init[90]: VO0: Type = 2, Sync = 9
box_init[67]: pch=AUTO
box_init[90]: VO1: Type = 0, Sync = 0
hifb info: vo max resolution w:128
Thu Jan 1 00:00:06 UTC 1970
PCI: enabling device 0000:00:02.0 (0040 -> 0043)
0x403f: latency timer and cache line value !
*************** bar5: b0020000
atp862x_His 0000:00:02.0: atp862x 0001.0000 32 slots 4 ports 3 Gbps 0xf impl unk
nown mode
atp862x_His 0000:00:02.0: flags: 64bit ncq led clo only pmp slum part
pdev->irq is 1d
hifb info: vo max resolution w:1280 h:1024
hifb info: The layer is show(1) now!
scsi0 : atp862x_His
scsi1 : atp862x_His
hifb info: vo max resolution w:720 h:576
hifb info: The layer is s
scsi2 : atp862x_His
scsi3 : atp862x_His
ata1: SATA max UDMA/133 abar m4096@0xb0020000 port 0x0 irq 29
ata2: SATA max UDMA/133 abar m4096@0xb0020000 port 0x80 irq 29
ata3: SATA max UDMA/133 abar m4096@0xb0020000 port 0x100 irq 29
ata4: SATA max UDMA/133 abar m4096@0xb0020000 port 0x180 irq 29
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
gv7601: CS0(0x006) = FFFF
gv7601: CS1(0x0
gv7601: CS2(0x006) = FFFF
gv7601: CS3(0x006) = FFFF
gv7601: chips = 4
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Driver 'sd' needs updating - please use bus_type methods
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered
usbcore: registered new interface driver usbserial_genericxit
run[27]: rtc_time = 94
drivers/usb/serial/usb-serial.c: USB Serial Driver coreHiDog: Unexpected close, not stopping watchdog!
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-00:00:00, diff = -946684783
dvr
port)1[121
usbcore: registered new interface driver option
Cannot connect to AP Server
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1annot connect to AP Server exit
Driver 'sr' needs updating - please use bus_type methodsit
reconnect...
modprobe: module ahci not found.xit
modprobe: failed to load module ahcionnect to AP Server exit
PPP generic driver version 2.4.2
Cannot connect to A
PPP Deflate Compression module registered
reconnect...

Cannot connect to AP Server exit
Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0,

(none) login: Cannot connect to AP Server ex
nodeamon= 0)
HISI_WDT-MDC030001 @Hi3511v110_OSDrv_1_0_0_8 2009-03-30 10:45:48<6>HISI_WDT-MDC0.

30001 @Hi3511v110_OSDrv_1_0_0_8 2009-03-30 10:45:48 to AP S
HISI_IRDA-MF @Hi3520v100R001_C_0_2_0 2010-06-29 22:34:49
reconnect...

hiir: init ok. ver=Jun 29 2010, 22:34:49.xi
RGMII=
ln: /dvr/oem/html/cgi-bin/net_jpeg.cgi: File exists

ln: /dvr/oem/html/cgi-bin/net_video.cgi: File exists

ln: /dvr/oem/html/cgi-bin/info.cgi: File exists Cannot
mount: Mounting /dev/mtdblock3 on /dvr/config failed: Device or resource busyServer exit
reconnect...
/dev/ttyS002 4
box_profile[133]: TW2868
Cannot connect to AP Ser
PHY: 0:01 - Link is Down

box_profile[205]: wait mcu_profilect...
box_profile[205]: wait mcu_profile Canno
insmod: cannot open module `/dvr/extdrv/keypad_main.ko': No such file or directo

ry
Cannt Open /dev/keypad
data1=0x7d28e241,data2=0xb18fc50c,data3=0x55f3cd2b,data4=0x2623216b
Cannot connect to AP Server exit
index=28,type=4CH-240

write virtual profile reconnect...
box_profile[284]: z_mcu = 4CH-240, m

dvr_hi3511[121]: UHiDog: Unexpected close, not stopping watchdog! Cannot connect to
nknow Vio Mode!!EXIT!!
/dev/ttyS001 4
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
resetting the transceiver...
Cannot connect to AP Server exit
reconnect...

(none) login: Cannot connect to AP Server exit
reconnect...


[dede]

Затереть вот этот диапазон: 0x00e80000-0x01000000 : "config"

[d37]

Прошивки на данный регистратор у меня нет, какие подготовительные работы сделать перед тем как давать команды:
sf probe 0
sf lock 0
sf erase 0x00e80000-0x01000000 : "config"

[d37]

Регистратор не реагирует на CTRL-C

[fobos]

или поменяйте адаптер или нажимайте CTRL-C до включения питания

[dtsatoll]

Затереть вот этот диапазон: 0x00e80000-0x01000000 : "config"

Здравствуйте, есть Neovizus NVD 216a, DVR-616-2 V1.2 не загружается, висит на заставке, через некоторое время перезагружается.
Прочитал всю ветку не понял как слить дамп. Слил с помощью программатора.
Подскажите как восстановить работоспособность аппарата.

[dtsatoll]

Лог:



NAND: 0 MiB


U-Boot 2008.10 (Jul 26 2011 - 21:22:58)

DRAM: 256 MB
## Unknown FLASH on Bank 2 - Size = 0x00000000 = 0 MB
Flash: 16 MB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Press CTRL-C to abort autoboot in alpum_set!!
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
## Booting kernel from Legacy Image at 80080000 ...
Image Name:
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1448408 Bytes = 1.4 MB
Load Address: e2800000
Entry Point: e2800000
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................ done, booting the kernel.
Linux version 2.6.24-rt1-hi3520v100 (root@ubuntu) (gcc version 3.4.3 (release) (CodeSourcery ARM Q3cvs 2004)) #17 Wed May 16 05:20:33 PDT 2012
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387f
Machine: hi3520v100
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 18288
Kernel command line: mem=72M console=ttyAMA0,115200 root=1f01 rootfstype=cramfs mtdparts=physmap-flash.0:5M(boot),6M(rootfs),3584k(oem),1536k(config) pcimod=host pciclksel=1 mac=00:17:4f:01:31:99 VDOSYS=PAL DDR=1G NET=MII
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 72MB = 72MB total
Memory: 69900KB available (2636K code, 242K data, 100K init)
Mount-cache hash table entries: 512
HI_VERSION=LINUX_2_6_24-M01C04FB01F @Hi3520v100R001_C_0_2_0 2010-03-12 13:45:01
CPU: Testing write buffer coherency: ok
net_namespace: 64 bytes
NET: Registered protocol family 16
Hisilicon clock system V0.01
PCI: device 0000:00:00.0 has unknown header type 25, ignoring.
PCI: device 0000:00:01.0 has unknown header type 25, ignoring.
PCI: device 0000:00:03.0 has unknown header type 14, ignoring.
PCI: device 0000:00:04.0 has unknown header type 14, ignoring.
PCI: device 0000:00:05.0 has unknown header type 14, ignoring.
PCI: device 0000:00:06.0 has unknown header type 14, ignoring.
PCI: device 0000:00:07.0 has unknown header type 14, ignoring.
PCI: device 0000:00:08.0 has unknown header type 14, ignoring.
PCI: device 0000:00:09.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0a.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0b.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0c.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0d.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0e.0 has unknown header type 14, ignoring.
PCI: device 0000:00:0f.0 has unknown header type 14, ignoring.
PCI: device 0000:00:10.0 has unknown header type 14, ignoring.
PCI: device 0000:00:11.0 has unknown header type 14, ignoring.
PCI: device 0000:00:12.0 has unknown header type 14, ignoring.
PCI: device 0000:00:13.0 has unknown header type 14, ignoring.
PCI: device 0000:00:14.0 has unknown header type 14, ignoring.
PCI: device 0000:00:15.0 has unknown header type 14, ignoring.
PCI: device 0000:00:16.0 has unknown header type 14, ignoring.
PCI: device 0000:00:17.0 has unknown header type 14, ignoring.
PCI: device 0000:00:18.0 has unknown header type 14, ignoring.
PCI: device 0000:00:19.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1a.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1b.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1c.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1d.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1e.0 has unknown header type 14, ignoring.
PCI: device 0000:00:1f.0 has unknown header type 14, ignoring.
PCI: bus0: Fast back to back transfers disabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: hisi_timer1 clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
yaffs Mar 25 2010 07:44:11 Installing.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20090000 (irq = 12) is a AMBA/PL011
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x200a0000 (irq = 12) is a AMBA/PL011
uart:2: ttyAMA2 at MMIO 0x200b0000 (irq = 13) is a AMBA/PL011
RAMDISK driver initialized: 4 RAM disks of 16384K size 4096 blocksize
loop: module loaded
physmap platform flash device: 04000000 at 80000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
4 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x00500000 : "boot"
0x00500000-0x00b00000 : "rootfs"
0x00b00000-0x00e80000 : "oem"
0x00e80000-0x01000000 : "config"
No NAND device found!!!
h2v100-ehci h2v100-ehci.0: h2v100-ehci
h2v100-ehci h2v100-ehci.0: new USB bus registered, assigned bus number 1
h2v100-ehci h2v100-ehci.0: irq 23, io mem 0x100b0000
h2v100-ehci h2v100-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
h2v100-ohci h2v100-ohci.0: h2v100-ohci
h2v100-ohci h2v100-ohci.0: new USB bus registered, assigned bus number 2
h2v100-ohci h2v100-ohci.0: irq 22, io mem 0x100a0000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
u32 classifier
Performance counters on
Netfilter messages via NETLINK v0.30.
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 100K
init started: BusyBox v1.1.2 (2010.10.12-04:51+0000) multi-call binary

_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
[RCS]: /etc/init.d/S20Cfg
RESO=1024x768
RESO_W=1024
RESO_H=768
NTSC_PAL_SW=1
AUTO=0
VDOSYS=PAL
NORM=2
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110104: 0x00009876 --> 0x00009654
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110100: 0x00000888 --> 0x00000886
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011010c: 0x00000001 --> 0x00000002
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110110: 0x00000002 --> 0x00000006
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110114: 0x00000003 --> 0x00000007
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110118: 0x00000005 --> 0x00000006
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011011c: 0x00000006 --> 0x00000007
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110128: 0x00000007 --> 0x00010020
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011012c: 0x00000007 --> 0x000103A1
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110130: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110134: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110138: 0x00000007 --> 0x00000004
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011013c: 0x00000007 --> 0x00000004
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050078: 0x00000000 --> 0x00008002
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120100: 0x00000444 --> 0x00000444
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120104: 0x00009876 --> 0x00009654
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012010c: 0x00000001 --> 0x00010640
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120110: 0x00000002 --> 0x00000003
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120114: 0x00000003 --> 0x00000004
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120118: 0x00Hisilicon Media Memory Zone Manager
000005 --> 0x00000001
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012011c: 0x00000006 --> 0x00000002
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120128: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012012c: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120130: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120134: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20120138: 0x00000007 --> 0x00000005
*** Board tools : ver0.0.1_20060106 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2012013c: 0x00000007 --> 0x00000005
[ipcm_vdd_init, 422]: local_cpu_id = 36

[ipcm_vdd_close, 268]: handle 0xc47d9540

[ipcm_vdd_init, 455]: IPCM hardware initialized successfully 0

hifb: module license 'Proprietary' taints kernel.
hifb info: HIFB_MAIN_VERSION[v1.0.0.2] Build Time[Sep 29 2010, 16:15:34]
hifb info: video:vram0_size=5242880,vram1_size=11538432,vram2_size=1658880,vram4_size=4096
hifb info: succeed in registering the fb0: ovl0 frame buffer device
hifb info: succeed in registering the fb1: ovl1 frame buffer device
hifb info: succeed in registering the fb2: ovl2 frame buffer device
hifb info: succeed in registering the fb3: ovl4 frame buffer device
TDE_MAIN_VERSION[v2.0.0.0] Build Time[Sep 29 2010, 16:15:28]
TDE_ADP_VERSION[hi3520adp v2.0.0.0] Build Time[Sep 29 2010, 16:15:28]
tde run on master arm
tde run for graphic service
tde map reg:basePhyAddr:20140000 baseVirAddr:c5074000 size:3000
Hisilicon UMAP device driver interface: v3.00
Chip Version: Hi35200100
load vd.ko ....OK!
load simd.ko OK
load vdec.ko ....OK
load vpp.ko ....OK!
load md.ko....OK!
insmod: cannot open module `hi3520_pciv_fmwm.ko': No such file or directory
nvp1104a driver init successful! chips = 0, norm = 2,audio stage=0
chips:2, norm:2
chips:2, norm:2
chips:2, norm:2
rn6264: version magic '2.6.24-rt1-hi3515v100 mod_unload ARMv5 ' should be '2.6.24-rt1-hi3520v100 mod_unload ARMv6 '
insmod: cannot insert `/dvr/extdrv/rn6264.ko': Invalid module format (-1): Exec format error
cat: /sys/module/rn6264/parameters/chips: No such file or directory
[: 0: unknown operand
VD=TW2868
VD_NORM=2
[ IPCM_Check, 222]: remote not ready, now connect and wait ...
[ IPCM_Check, 252]: remote connected
box_init[67]: pch=1024x768
box_init[90]: VO0: Type = 2, Sync = 8
box_init[67]: pch=AUTO
box_init[90]: VO1: Type = 0, Sync = 0
hifb info: vo max resolution w:1024 h:768
cat9883c_device_init[163]: mode=1, 0x34
Thu Jan 1 00:00:05 UTC 1970
PCI: enabling device 0000:00:02.0 (0040 -> 0043)
0x403f: latency timer and cache line value !
*************** bar5: b0020000
atp862x_His 0000:00:02.0: atp862x 0001.0000 32 slots 4 ports 3 Gbps 0xf impl unknown mode
atp862x_His 0000:00:02.0: flags: 64bit ncq led clo only pmp slum part
pdev->irq is 1d
hifb info: vo max resolution w:1024 h:768
hifb info: The layer is show(1) now!
scsi0 : atp862x_His
hifb info: vo max resolution w:720 h:576
hifb info: The layer is show(1) now!
scsi1 : atp862x_His
scsi2 : atp862x_His
scsi3 : atp862x_His
ata1: SATA max UDMA/133 abar m4096@0xb0020000 port 0x0 irq 29
ata2: SATA max UDMA/133 abar m4096@0xb0020000 port 0x80 irq 29
ata3: SATA max UDMA/133 abar m4096@0xb0020000 port 0x100 irq 29
ata4: SATA max UDMA/133 abar m4096@0xb0020000 port 0x180 irq 29
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
gv7601: CS0(0x006) = FFFF
gv7601: CS1(0x006) = FFFF
gv7601: CS2(0x006) = FFFF
gv7601: CS3(0x006) = FFFF
gv7601: chips = 4
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Driver 'sd' needs updating - please use bus_type methods
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
Driver 'sr' needs updating - please use bus_type methods
modprobe: module ahci not found.
modprobe: failed to load module ahci
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
usbcore: registered new interface driver TouchKit
acer_init
usbcore: registered new interface driver acer_t230h
insmod: cannot open module `/dvr/extdrv/pl230': No such file or directory
Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 0)
HISI_WDT-MDC030001 @Hi3511v110_OSDrv_1_0_0_8 2009-03-30 10:45:48<6>HISI_WDT-MDC030001 @Hi3511v110_OSDrv_1_0_0_8 2009-03-30 10:45:48
HISI_IRDA-MF @Hi3520v100R001_C_0_2_0 2010-06-29 22:34:49
hiir: init ok. ver=Jun 29 2010, 22:34:49.
RGMII=
H2GMAC module init start!
H2GMAC MDIO Bus: probed
H2GMAC module init done!
NET: Registered protocol family 17
/etc/init.d/S20Cfg: /etc/init.d/S20Cfg: 233: /dvr/config/run: not found
ln: /dvr/oem/html/cgi-bin/net_html.cgi: File exists
ln: /dvr/oem/html/cgi-bin/net_jpeg.cgi: File exists
ln: /dvr/oem/html/cgi-bin/net_video.cgi: File exists
ln: /dvr/oem/html/cgi-bin/info.cgi: File exists
mount: Mounting /dev/mtdblock3 on /dvr/config failed: Device or resource busy
/dev/ttyS002 4
box_profile[88]: TW2868
dvr_vd_tw2868[13]: ############# m_chips=2
get_ch_num[28]: ##########m_chips=2
box_profile[112]: z_chnum = 16, z_ntsc = 0, z_mdin = 0
box_profile[160]: wait mcu_profile
PHY: 0:01 - Link is Down
box_profile[160]: wait mcu_profile
PHY: 0:01 - Link is Up - 100/Full
box_profile[160]: wait mcu_profile
insmod: cannot open module `/dvr/extdrv/keypad_main.ko': No such file or directory
Cannt Open /dev/keypad
data1=0x7d28e241,data2=0xb18fc50c,data3=0x55f3cd2b,data4=0x2623216b
index=28,type=4CH-240
write virtual profile
box_profile[239]: z_mcu = 4CH-240, mcu_idx = 5
box_profile[249]: a = 1, b = 0, c = 0
box_profile[266]: oem_id=ddfa0432
box_ftp[6]: enter!!
set_timeout[44]: WDIOC_SETTIMEOUT = 60s
dvr_vd_tw2868[13]: ############# m_chips=2
dvr_ap[185]: ALPU CHECK
dvr_hi3511[121]: UHiDog: Unexpected close, not stopping watchdog!
nknow Vio Mode!!EXIT!!
/dev/ttyS001 4
Cannot connect to AP Server exit
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
resetting the transceiver...
reconnect...
Cannot connect to AP Server exit

(none) login: reconnect...
Cannot connect to AP Server exit
PHY: 0:01 - Link is Down
reconnect...
Cannot connect to AP Server exit
PHY: 0:01 - Link is Up - 100/Full
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...
Cannot connect to AP Server exit
reconnect...

[dtsatoll]

Затереть вот этот диапазон: 0x00e80000-0x01000000 : "config"

какой командой затереть?
erase 0x00e80000-0x01000000 ?