DVR 1208AHD-N висит после заставки

[yuri1958]

На плате наклейка HY-BH-8286-8-T и надпись DATA:2016-06-17 8286_6134C_V1.0
После включения заставка цветные полосы, после заставки черный экран и постоянная пеерезагрузка
В терминал выдает:

U-Boot 2013.01 (Dec 18 2017 - 17:13:26)

DRAM: 256 MiB
ROM CODE has enable I cache
SPI mode
SF: Got idcodes
00000000: ef 40 17 00 .@..
SF: Detected W25Q64 with page size 64 KiB, total 8 MiB
flash is 3byte mode
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial

-------------------------------
ID:82860003
AC: 332 HC: 249 P1: 996 P4: 996
C6: 664 DR:1328
J: 249 H1: 398 H2: 398
-------------------------------
Net: GMAC set RMII mode
reset PHY
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 3d:73:71:75:61:73
Address in environment is 00:42:70:00:30:22

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Hit any key to stop autoboot: 3 0GM8286 SYSTEM go.................DR 1.3 256MB
MP SPI-NOR Bootstrap v0.1
SPI020 Revision:0x10001
SPI flash ID code:ef 40 17
SPI jump setting is 3 bytes mode
Boot image offset: 0x10000. size: 0x40000. Booting Image .....


U-Boot 2013.01 (Dec 18 2017 - 17:13:26)

DRAM: 256 MiB
ROM CODE has enable I cache
SPI mode
SF: Got idcodes
00000000: ef 40 17 00 .@..
SF: Detected W25Q64 with page size 64 KiB, total 8 MiB
flash is 3byte mode
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial

-------------------------------
ID:82860003
AC: 332 HC: 249 P1: 996 P4: 996
C6: 664 DR:1328
J: 249 H1: 398 H2: 398
-------------------------------
Net: GMAC set RMII mode
reset PHY
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 3d:73:71:75:61:73
Address in environment is 00:42:70:00:30:22

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Hit any key to stop autoboot: 0
start hdmi polling thread.
sli-hdmi is in 1920x1080 RGBI2C_IP1_init APB freq = 41500000
I2C_IP1_init: speed: 100000, div = 204
Please plug-in the HDMI cable, otherwise the system may keep wating the connecti
on....
SF: Got idcodes
00000000: ef 40 17 00 .@..
SF: Detected W25Q64 with page size 64 KiB, total 8 MiB
flash is 3byte mode
## Booting kernel from Legacy Image at 02000000 ...
Image Name: gm828x
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2237856 Bytes = 2.1 MiB
Load Address: 02000000
Entry Point: 02000040
Verifying Checksum ... OK
XIP Kernel Image ... OK
OK
: mem=256M gmmem=190M console=ttyS0,115200 user_debug=31 init=/squashfs_init roo
t=/dev/mtdblock3 rootfstype=squashfs

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0
Linux version 3.3.0 (amos@HYServer) (gcc version 4.4.0 20100318 (experimental) (
Buildroot 2012.02) ) #82 PREEMPT Mon Mar 20 10:50:42 CST 2017
CPU: FA6 [66056262] revision 2 (ARMv5TE), cr=0000397f
CPU VIPT aliasing data cache, unknown instruction cache
Machine: Grain-Media GM828x series
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: mem=256M gmmem=190M console=ttyS0,115200 user_debug=31 init
=/squashfs_init root=/dev/mtdblock3 rootfstype=squashfs
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 255300k/255300k available, 6844k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0x90800000 - 0xff000000 (1768 MB)
lowmem : 0x80000000 - 0x90000000 ( 256 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x803fbad8 (4047 kB)
.init : 0x803fc000 - 0x80417000 ( 108 kB)
.data : 0x80418000 - 0x80437640 ( 126 kB)
.bss : 0x80437664 - 0x8047129c ( 232 kB)
NR_IRQS:96
Timer use APB0 clock
gm_jiffies_init, system HZ: 100, pClk: 41500000
console [ttyS0] enabled
Calibrating delay loop... 660.68 BogoMIPS (lpj=3303424)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x2fdba8 - 0x2fdbf0
devtmpfs: initialized
FMEM: 48640 pages(0xbe00000 bytes) from bank0 are reserved for Frammap.
FMEM: Logical memory ends up at 0x90000000, init_mm:0x80004000(0x4000), PAGE_OFF
SET:0x80000000(0x0),
FMEM: FA726 Test and Debug Register: 0x0
NET: Registered protocol family 16
PMU: Mapped at 0xfe000000
IC: GM8286, version: 0x3
iotable: VA: 0xfe000000, PA: 0x99000000, Length: 4096
iotable: VA: 0xfe001000, PA: 0x98300000, Length: 4096
iotable: VA: 0xfe002000, PA: 0x98400000, Length: 4096
iotable: VA: 0xfe003000, PA: 0x98500000, Length: 4096
iotable: VA: 0xfe004000, PA: 0x98800000, Length: 4096
iotable: VA: 0xfe005000, PA: 0x99100000, Length: 4096
iotable: VA: 0xfe006000, PA: 0x96000000, Length: 4096
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource fttmr010:1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Video Timer(timer3) Max 103000ms in 0xfec7b1a0 HZ.
ftdmac020 ftdmac020.0: DMA engine driver: irq 1, mapped at 0x90804000
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
msgmni has been set to 498
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
gpiochip_add: registered GPIOs 0 to 31 on device: ftgpio010.0
probe ftgpio010.0 OK, at 0x90862000
gpiochip_add: registered GPIOs 32 to 63 on device: ftgpio010.1
probe ftgpio010.1 OK, at 0x90864000
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xfe001000 (irq = 9) is a 16550A
serial8250: ttyS1 at I/O 0xfe002000 (irq = 10) is a 16550A
brd: module loaded
loop: module loaded
FTSATA100_AHCI driver version 0.15
GM SATAPHY clock source : SATA0==SATA1, SATA1==PLL
GM SATAPHY Clock = 30 MHz
GM SATA0 config iSATA PHY setting
GM SATA0 PHY program i2c register offset 0x07, value=0x09
GM SATA0 PHY program i2c register offset 0x19, value=0x0c
GM SATA0 PHY program i2c register offset 0x35, value=0x10
GM SATA0 PHY program i2c register offset 0x36, value=0x80
GM SATA1 config iSATA PHY setting
GM SATA1 PHY program i2c register offset 0x07, value=0x09
GM SATA1 PHY program i2c register offset 0x19, value=0x0c
GM SATA1 PHY program i2c register offset 0x35, value=0x10
GM SATA1 PHY program i2c register offset 0x36, value=0x80
ahci ftsata100.0: forcing PORTS_IMPL to 0x1
ahci: SSS flag set, parallel bus scan disabled
ahci ftsata100.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ftsata100.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc
scsi0 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x93200000-0x93200fff] port 0x100 irq 28
ahci ftsata100.1: forcing PORTS_IMPL to 0x1
ahci: SSS flag set, parallel bus scan disabled
ata1: SATA link down (SStatus 0 SControl 310)
ahci ftsata100.1: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ftsata100.1: flags: ncq sntf stag pm led clo only pmp pio slum part ccc
scsi1 : ahci_platform
ata2: SATA max UDMA/133 mmio [mem 0x93300000-0x93300fff] port 0x100 irq 40
Not for NAND pin mux
SPI020 init
ftspi020 ftspi020.0: Faraday FTSPI020 Controller at 0x80300000(0x9086e000) irq 9
2.
spi spi0.0: setup: bpw 8 mode 0
CLK div field set 2, clock = 41500000Hz
ERASE SECTOR 64K
SPI_FLASH spi0.0: w25Q64F (8192 Kbytes)
Creating 10 MTD partitions on "nor-flash":
0x000000000000-0x000000010000 : "NSBOOT"
0x000000010000-0x000000050000 : "UBOOT"
0x000000050000-0x000000280000 : "LINUX"
0x000000280000-0x000000400000 : "FS"
0x000000400000-0x000000450000 : "SAV"
0x000000450000-0x000000740000 : "USER"
0x000000740000-0x0000007d0000 : "WEB"
0x0000007d0000-0x0000007e0000 : "LOG"
0x0000007e0000-0x000000800000 : "CUSTOM"
0x000000000000-0x000000800000 : "ALL"
Probe FTSPI020 SPI Controller at 0x80300000 (irq 92)
ftgmac: Loading version 2.0 ...
ftgmac: Tx queue number = 1024, Rx queue number = 512
ata2: SATA link down (SStatus 0 SControl 310)
ftgmac100-0-mdio: probed
ftgmac100-0 ftgmac100-0.0: eth0: 1 tx queue used (max: 2)
ftgmac100-0 ftgmac100-0.0: eth0: 1 rx queue used (max: 1)
ftgmac100-0 ftgmac100-0.0: eth0: irq 3, mapped at 90870000
ftgmac100-0 ftgmac100-0.0: eth0: generated random MAC address 42:d8:31:8a:da:bc
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
FOTG2XX Controller Initialization
Enter Device A
Drive Vbus because of ID pin shows Device A
fotg210 fotg210.0: FOTG2XX
fotg210 fotg210.0: new USB bus registered, assigned bus number 1
fotg210 fotg210.0: irq 93, io mem 0x93000000
fotg210 fotg210.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
FOTG2XX Controller Initialization
Enter Device A
Drive Vbus because of ID pin shows Device A
fotg210 fotg210.1: FOTG2XX
fotg210 fotg210.1: new USB bus registered, assigned bus number 2
fotg210 fotg210.1: irq 94, io mem 0x93100000
fotg210 fotg210.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
ftiic010 ftiic010.0: irq 18, mapped at 90876000
ftiic010 ftiic010.1: irq 53, mapped at 90878000
ftiic010 ftiic010.2: irq 50, mapped at 9087a000
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
devtmpfs: mounted
Пробовал подключать HDMI тоже самое.Клиент говорит заклинил после скачка напряжения в сети.

[yuri1958]

Слил дамп , прилагаю http://rgho.st/6BFhLKS5n" onclick="window.open(this.href);return false;
кто может подсказать какой раздел почистить USER или SAV что бы сбросить конфиг

[dede]

по идее - SAV

[yuri1958]

Затер раздел SAV рег висит на заставке,в терминале

~ # 0GM8286 SYSTEM go.................DR 1.3 256MB
MP SPI-NOR Bootstrap v0.1
SPI020 Revision:0x10001
SPI flash ID code:ef 40 17
SPI jump setting is 3 bytes mode
Boot image offset: 0x10000. size: 0x40000. Booting Image .....


U-Boot 2013.01 (Dec 18 2017 - 17:13:26)

DRAM: 256 MiB
ROM CODE has enable I cache
SPI mode
SF: Got idcodes
00000000: ef 40 17 00 .@..
SF: Detected W25Q64 with page size 64 KiB, total 8 MiB
flash is 3byte mode
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial

-------------------------------
ID:82860003
AC: 332 HC: 249 P1: 996 P4: 996
C6: 664 DR:1328
J: 249 H1: 398 H2: 398
-------------------------------
Net: GMAC set RMII mode
reset PHY
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 3d:73:71:75:61:73
Address in environment is 00:42:70:00:30:22

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Hit any key to stop autoboot: 0
GM # 0GM8286 SYSTEM go.................DR 1.3 256MB
MP SPI-NOR Bootstrap v0.1
SPI020 Revision:0x10001
SPI flash ID code:ef 40 17
SPI jump setting is 3 bytes mode
Boot image offset: 0x10000. size: 0x40000. Booting Image .....


U-Boot 2013.01 (Dec 18 2017 - 17:13:26)

DRAM: 256 MiB
ROM CODE has enable I cache
SPI mode
SF: Got idcodes
00000000: ef 40 17 00 .@..
SF: Detected W25Q64 with page size 64 KiB, total 8 MiB
flash is 3byte mode
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial

-------------------------------
ID:82860003
AC: 332 HC: 249 P1: 996 P4: 996
C6: 664 DR:1328
J: 249 H1: 398 H2: 398
-------------------------------
Net: GMAC set RMII mode
reset PHY
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 3d:73:71:75:61:73
Address in environment is 00:42:70:00:30:22

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Hit any key to stop autoboot: 3 0GM8286 SYSTEM go.................DR 1.3 256MB
MP SPI-NOR Bootstrap v0.1
SPI020 Revision:0x10001
SPI flash ID code:ef 40 17
SPI jump setting is 3 bytes mode
Boot image offset: 0x10000. size: 0x40000. Booting Image .....


U-Boot 2013.01 (Dec 18 2017 - 17:13:26)

DRAM: 256 MiB
ROM CODE has enable I cache
SPI mode
SF: Got idcodes
00000000: ef 40 17 00 .@..
SF: Detected W25Q64 with page size 64 KiB, total 8 MiB
flash is 3byte mode
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial

-------------------------------
ID:82860003
AC: 332 HC: 249 P1: 996 P4: 996
C6: 664 DR:1328
J: 249 H1: 398 H2: 398
-------------------------------
Net: GMAC set RMII mode
reset PHY
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is 3d:73:71:75:61:73
Address in environment is 00:42:70:00:30:22

(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Hit any key to stop autoboot: 0
GM # help
? - alias for 'help'
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootlogo- show lcd bootlogo
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
dcache - enable or disable data cache
env - environment handling commands
erase - erase FLASH memory
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
fatwrite- write file into a dos filesystem
flinfo - print FLASH memory information
fwupd - firmware upgrade from usb device for specified filename
go - start application at address 'addr'
help - print command description/usage
icache - enable or disable instruction cache
l2cache_test- Perform test of L2 cache
md - memory display
memtester- memory tester
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mtest - simple RAM read/write test
mw - memory write (fill)
nm - memory modify (constant address)
printenv- print environment variables
protect - enable or disable FLASH write protection
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sf - SPI flash sub-system
sspi - SPI utility command
tftpboot- boot image via network using TFTP protocol
usb - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
GM # version

U-Boot 2013.01 (Dec 18 2017 - 17:13:26)
arm-unknown-linux-uclibcgnueabi-gcc (Buildroot 2012.02) 4.4.0 20100318 (experime
ntal)
GNU ld (GNU Binutils) 2.21.1
GM # printenv
auimg0=u-boot_spi_RMII.bin
auimg1=uImage_828x
auimg2=rootfs-cpio_828x.squashfs.img
auimg3=mtd.img
auimgaio=flash.img
auimgbot=nsboot.bin
autoupdate=no
baudrate=115200
bootcmd=bootlogo hdmi;sf probe 0:0;run lm;bootm 0x2000000
bootdelay=3
cmd2=mem=256M gmmem=190M console=ttyS0,115200 user_debug=31 init=/squashfs_init
root=/dev/mtdblock3 rootfstype=squashfs
cmd3=mem=256M gmmem=190M console=ttyS0,115200 user_debug=31 init=/squashfs_init
root=/dev/mtdblock3 rootfstype=squashfs
cmd6=mem=256M gmmem=190M console=ttyS0,115200 user_debug=31 init=/squashfs_init
root=/dev/mtdblock3 rootfstype=squashfs
cmd7=mem=256M gmmem=190M console=ttyS0,115200 user_debug=31 init=/squashfs_init
root=/dev/mtdblock3 rootfstype=squashfs
ethact=eth0
ethaddr=00:42:70:00:30:22
gatewayip=10.0.1.51
ipaddr=10.0.1.52
lm=sf read 0x02000000 z
netmask=255.0.0.0
serverip=10.0.1.51
stderr=serial
stdin=serial
stdout=serial

Environment size: 943/65532 bytes
GM # usbboot
** No device specified **
GM #

Наверное дамп битый. Хочу попробовать дамп от HVR508 V1. залить на 16 метровую флешку,у него проц и кодер одинаковые может заработает.

[dede]

Есть и прошивки и дампы на эти реги. Поиск без проблем находит http://www.dvrsoftwareservice.com/dvrso ... /flash.bin" onclick="window.open(this.href);return false;

[yuri1958]

Я оттуда прошивку 5608L-N-nvp6134C скачал, дамп найти что-то не вышло там. Залил в 16 метровую флешку дамп от XVR508 V1 , а потом обновил прошивкой с сайта. Получился DVR5608L-N. Все прекрасно работает, по серийнику в локалке подключился через приложение N_eye_Pro к регу затем пробросил 8000 и 5000 порты на роутере и рег без регистрации виден через интернет на телефоне. Но все равно интересует вопрос почему с 8 метровой флешкой и родной прошивкой рег висел на заставке после зачистки раздела SAV?

[Sonya]

Но все равно интересует вопрос почему с 8 метровой флешкой и родной прошивкой рег висел на заставке после зачистки раздела SAV?

Так может уже та 8Мб флешка была битая?

[yuri1958]

На новую флешку дамп заливал и верификацию делал . Тут что-то другое. Хотелось бы разобраться, но рег сегодня забирают. Реги с процом GM8286 редко попадают на ремонт.

[yuri1958]

Обнаружил дефект. После перезагрузки меняется системное время на 2000.01.01 ,напряжение на батарейке в норме 3.2 вольт. Поменял таймер DS1307 и часовой кварц , время также сбивается на 2000.01.01 , на кварце генерация есть. Если включаю синхронизацию времени с интернетом, время устанавливается правильно. Где засада не пойму никак. На шине I2C движение есть.По даташиту в режиме покоя таймер должен работать от батарейки, а получается что он обнуляется и не запоминает данные как должно быть. Может кто сталкивался с такой неисправностью подскажите где искать?

[dede]

Не подошла прошивка. Пробуйте ваши, 8 меговые, тогда

[yuri1958]

Не подошла прошивка. Пробуйте ваши, 8 меговые, тогда

8 меговых рабочих ни прошивки ни дампа нету. Если только кто поможет 8 меговый дамп поправить. На сайте только 16 метровые прошивки на HY DVR 5608L У меня модель 1208AHD-N
Под GM8286 8 метровых прошивок найти не получается.

[dede]

Да уж, у вас какой-то обрезок, DVR-5308L-N/T