Добрый день! Проблема с Apix-Box/M1, камеры слетели на заводские настройки. При изменении Ip адреса в веб-интерфейсе камера перезагружается и вновь отвечает только на дефолтном ip, также при попытке добавить пользователя камера «подвисает» и оживает только после ресета с кнопки или перезагрузки по питанию с опять же заводскими настройками. На камере открыт телнет, но изменить адрес в /etc/network/interfaces не дает (нет свободного места), при изменении адреса через ifconfig камера дает зайти на веб интерфейс и по телнету на новом IP до перезагрузки, при этом настройки сети в веб морде дефолтные. Пробовал сменить разные прошивки (userland.jffs2) от саппорта через веб интерфейс, но камеры не принимают ни одну прошивку- выдает fatal error. Версия железа с веб интерфейсса CCD-cameraFw-100811P, версия прошивки p20120914NS. На платах не нашел uart. Фотки ниже. Причем такая же беда с Apix-VDome/M1 3312. Проверял батарейки.
https://yadi.sk/i/s91fUT8WOlGsxQ" onclick="window.open(this.href);return false;
https://yadi.sk/i/kavOxuWu2ezGZA" onclick="window.open(this.href);return false;
https://yadi.sk/i/lPrv015jQGcgqg" onclick="window.open(this.href);return false;
глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
Sony CXD3182GG
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
Флеш какая стоит? На фото надписи не видно. Слить дамп на програматоре и перезалить в новую флеш. Родная флешка возможно сдохла поэтому не сохраняет настройки.
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
epidata twn d51323dbh-6els-f на плате 3 штуки
такой глюк на 20 устройствах
такой глюк на 20 устройствах
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
флешки не монтируются
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
Или намного проще - побился жффс2 с настройками. Выкладывайте dmesg и cat /proc/mtd
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
~ #cat /proc/mtd
dev: size erasesize name
mtd0: 00040000 00020000 "U-Boot Bin Area"
mtd1: 00040000 00020000 "U-Boot Param Save Area"
mtd2: 00020000 00020000 "ARM9 Comm Param Save Area"
mtd3: 00020000 00020000 "Cam FW Set Param Save Area(Bank A)"
mtd4: 00020000 00020000 "Cam FW Set Param Save Area(Bank B)"
mtd5: 00020000 00020000 "Cam FW Defect Revision Data Area"
mtd6: 00040000 00020000 "Reserved Area 1"
mtd7: 00020000 00020000 "ARM9 Comm Param Default Data Area"
mtd8: 00020000 00020000 "Cam FW Set Param Default Data Area"
mtd9: 00020000 00020000 "Initial OSD Color Palette Area"
mtd10: 00020000 00020000 "Initial OSD Data Area"
mtd11: 00020000 00020000 "Initial Mask Data Area"
mtd12: 00100000 00020000 "Reserved Area 2"
mtd13: 00100000 00020000 "ARM9 F/W Bin Area"
mtd14: 00420000 00020000 "Kernel Image Area"
mtd15: 01700000 00020000 "Userland(jffs2) Area"
mtd16: 00100000 00020000 "Dyna"
dev: size erasesize name
mtd0: 00040000 00020000 "U-Boot Bin Area"
mtd1: 00040000 00020000 "U-Boot Param Save Area"
mtd2: 00020000 00020000 "ARM9 Comm Param Save Area"
mtd3: 00020000 00020000 "Cam FW Set Param Save Area(Bank A)"
mtd4: 00020000 00020000 "Cam FW Set Param Save Area(Bank B)"
mtd5: 00020000 00020000 "Cam FW Defect Revision Data Area"
mtd6: 00040000 00020000 "Reserved Area 1"
mtd7: 00020000 00020000 "ARM9 Comm Param Default Data Area"
mtd8: 00020000 00020000 "Cam FW Set Param Default Data Area"
mtd9: 00020000 00020000 "Initial OSD Color Palette Area"
mtd10: 00020000 00020000 "Initial OSD Data Area"
mtd11: 00020000 00020000 "Initial Mask Data Area"
mtd12: 00100000 00020000 "Reserved Area 2"
mtd13: 00100000 00020000 "ARM9 F/W Bin Area"
mtd14: 00420000 00020000 "Kernel Image Area"
mtd15: 01700000 00020000 "Userland(jffs2) Area"
mtd16: 00100000 00020000 "Dyna"
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
вложить текстовый файлик не дает.
dmesg
Linux version 2.6.21.7-hrt1nessy3-WR2.0bl_small (root@localhost.localdomain) (gcc version 4.1.2 (Wind River Linux Sourcery G++ 4.1-84)) #2 PREEMPT Wed Apr 7 14:57:42 CST 2010
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387f
Machine: Sony Nessy3
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 8192
DMA zone: 64 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 8128 pages, LIFO batch:0
Normal zone: 0 pages used for memmap
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 8128
Kernel command line: root=/dev/mtdblock15 rootfstype=jffs2 ip=192.168.0.250:192.168.0.20:192.168.0.254:255.255.255.0::eth0: console=ttyAMA0, 38400n8 mem=32M
Enable VIC1 : fffffd45
Enable VIC2 : d010c9f7
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 28828KB available (3260K code, 254K data, 100K init)
Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
zcorepcieroot_pci_init : pinmux flag 0
zcorepcieroot_pci_init : root core initialize NG
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 2, 20480 bytes)
TCP bind hash table entries: 1024 (order: 2, 20480 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
Registering GDB sysrq handler
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
Registering unionfs 2.1.6 (for 2.6.21.7)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
LTT : ltt-facilities init
LTT : ltt-relay init
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
Serial: AMBA PL011 UART driver
IC2_APB:UART3: ttyAMA0 at MMIO map 0x30007000 mem 0xc2850000 (irq = 24) is a AMBA/PL011
smac: enable jumbo frame
smac: enable napi
smac: enable sw csum
smac: eth0: smac_init_module: SMAC Network Connection (eth0)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
i2c /dev entries driver
nessy3_nor_flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
nessy3_nor_flash.0: Found an alias at 0x2000000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
nessy3_nor_flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 17 MTD partitions on "nessy3_nor_flash.0":
0x00000000-0x00040000 : "U-Boot Bin Area"
0x00040000-0x00080000 : "U-Boot Param Save Area"
0x00080000-0x000a0000 : "ARM9 Comm Param Save Area"
0x000a0000-0x000c0000 : "Cam FW Set Param Save Area(Bank A)"
0x000c0000-0x000e0000 : "Cam FW Set Param Save Area(Bank B)"
0x000e0000-0x00100000 : "Cam FW Defect Revision Data Area"
0x00100000-0x00140000 : "Reserved Area 1"
0x00140000-0x00160000 : "ARM9 Comm Param Default Data Area"
0x00160000-0x00180000 : "Cam FW Set Param Default Data Area"
0x00180000-0x001a0000 : "Initial OSD Color Palette Area"
0x001a0000-0x001c0000 : "Initial OSD Data Area"
0x001c0000-0x001e0000 : "Initial Mask Data Area"
0x001e0000-0x002e0000 : "Reserved Area 2"
0x002e0000-0x003e0000 : "ARM9 F/W Bin Area"
0x003e0000-0x00800000 : "Kernel Image Area"
0x00800000-0x01f00000 : "Userland(jffs2) Area"
0x01f00000-0x02000000 : "Dyna"
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
smac: eth0: smac_open: smac version: 0.0.2-NAPI-JUMBO
smac: eth0: smac_open: hw version: 0.5.11.23
smac: eth0: smac_request_irq: irq:2
ADDRCONF(NETDEV_UP): eth0: link is not ready
IP-Config: Complete:
device=eth0, addr=192.168.0.250, mask=255.255.255.0, gw=192.168.0.254,
host=192.168.0.250, domain=, nis-domain=(none),
bootserver=192.168.0.20, rootserver=192.168.0.20, rootpath=
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 100K
smac: eth0: smac_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
arm9_mailbox: module license 'Proprietary' taints kernel.
arm9_mailbox: successfully installed.(major=235, irq=0, irq_id=arm9_mailbox interrupt)
i2c-algo-i2c00: I2C00 (i2c) algorithm module
i2c-adap-i2c00: i2c I2C00 adapter driver
i2c-adap-i2c00: I2C00 ID = 01500000
rtc-rs5c372 0-0032: assuming rv5c387a
rtc-rs5c372 0-0032: rv5c387a found, 24hr, driver version 0.4
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
i2c-adap-i2c00: found device at 0x30003000
i2c-adap-i2c00: use irq at 22
pl061_gpio_a: major=220, irq=non
pl061_gpio_f: major=225, irq=21
pl061_gpio_g: major=226, irq=non
sdif_driver : Major Number 240
sdif_driver : SSDIF_LINUX_H = C1519000
sdif_driver : SSDIF_LINUX_H->card.dev.address = C28C0000
sdif_driver : complete insmod
PL080 DMAC Driver : IRQ 8
PCIeDMAC Driver : irq_no 10
### pccregdrv ### <7>pccreg_cdev_init
smac: eth0: smac_reset: hw tx done
smac: eth0: smac_reset: sw reset done
smac: eth0: smac_open: smac version: 0.0.2-NAPI-JUMBO
smac: eth0: smac_open: hw version: 0.5.11.23
smac: eth0: smac_request_irq: irq:2
ADDRCONF(NETDEV_UP): eth0: link is not ready
smac: eth0: smac_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
sdif_driver : sdif_block_open
sdif_driver : SDIF_Card_MemoryOpen = 7
eth0: no IPv6 routers present
dmesg
Linux version 2.6.21.7-hrt1nessy3-WR2.0bl_small (root@localhost.localdomain) (gcc version 4.1.2 (Wind River Linux Sourcery G++ 4.1-84)) #2 PREEMPT Wed Apr 7 14:57:42 CST 2010
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387f
Machine: Sony Nessy3
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 8192
DMA zone: 64 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 8128 pages, LIFO batch:0
Normal zone: 0 pages used for memmap
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 8128
Kernel command line: root=/dev/mtdblock15 rootfstype=jffs2 ip=192.168.0.250:192.168.0.20:192.168.0.254:255.255.255.0::eth0: console=ttyAMA0, 38400n8 mem=32M
Enable VIC1 : fffffd45
Enable VIC2 : d010c9f7
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 28828KB available (3260K code, 254K data, 100K init)
Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
zcorepcieroot_pci_init : pinmux flag 0
zcorepcieroot_pci_init : root core initialize NG
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 2, 20480 bytes)
TCP bind hash table entries: 1024 (order: 2, 20480 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
Registering GDB sysrq handler
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
Registering unionfs 2.1.6 (for 2.6.21.7)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
LTT : ltt-facilities init
LTT : ltt-relay init
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
Serial: AMBA PL011 UART driver
IC2_APB:UART3: ttyAMA0 at MMIO map 0x30007000 mem 0xc2850000 (irq = 24) is a AMBA/PL011
smac: enable jumbo frame
smac: enable napi
smac: enable sw csum
smac: eth0: smac_init_module: SMAC Network Connection (eth0)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
i2c /dev entries driver
nessy3_nor_flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
nessy3_nor_flash.0: Found an alias at 0x2000000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
nessy3_nor_flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 17 MTD partitions on "nessy3_nor_flash.0":
0x00000000-0x00040000 : "U-Boot Bin Area"
0x00040000-0x00080000 : "U-Boot Param Save Area"
0x00080000-0x000a0000 : "ARM9 Comm Param Save Area"
0x000a0000-0x000c0000 : "Cam FW Set Param Save Area(Bank A)"
0x000c0000-0x000e0000 : "Cam FW Set Param Save Area(Bank B)"
0x000e0000-0x00100000 : "Cam FW Defect Revision Data Area"
0x00100000-0x00140000 : "Reserved Area 1"
0x00140000-0x00160000 : "ARM9 Comm Param Default Data Area"
0x00160000-0x00180000 : "Cam FW Set Param Default Data Area"
0x00180000-0x001a0000 : "Initial OSD Color Palette Area"
0x001a0000-0x001c0000 : "Initial OSD Data Area"
0x001c0000-0x001e0000 : "Initial Mask Data Area"
0x001e0000-0x002e0000 : "Reserved Area 2"
0x002e0000-0x003e0000 : "ARM9 F/W Bin Area"
0x003e0000-0x00800000 : "Kernel Image Area"
0x00800000-0x01f00000 : "Userland(jffs2) Area"
0x01f00000-0x02000000 : "Dyna"
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
smac: eth0: smac_open: smac version: 0.0.2-NAPI-JUMBO
smac: eth0: smac_open: hw version: 0.5.11.23
smac: eth0: smac_request_irq: irq:2
ADDRCONF(NETDEV_UP): eth0: link is not ready
IP-Config: Complete:
device=eth0, addr=192.168.0.250, mask=255.255.255.0, gw=192.168.0.254,
host=192.168.0.250, domain=, nis-domain=(none),
bootserver=192.168.0.20, rootserver=192.168.0.20, rootpath=
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 100K
smac: eth0: smac_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
arm9_mailbox: module license 'Proprietary' taints kernel.
arm9_mailbox: successfully installed.(major=235, irq=0, irq_id=arm9_mailbox interrupt)
i2c-algo-i2c00: I2C00 (i2c) algorithm module
i2c-adap-i2c00: i2c I2C00 adapter driver
i2c-adap-i2c00: I2C00 ID = 01500000
rtc-rs5c372 0-0032: assuming rv5c387a
rtc-rs5c372 0-0032: rv5c387a found, 24hr, driver version 0.4
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
i2c-adap-i2c00: found device at 0x30003000
i2c-adap-i2c00: use irq at 22
pl061_gpio_a: major=220, irq=non
pl061_gpio_f: major=225, irq=21
pl061_gpio_g: major=226, irq=non
sdif_driver : Major Number 240
sdif_driver : SSDIF_LINUX_H = C1519000
sdif_driver : SSDIF_LINUX_H->card.dev.address = C28C0000
sdif_driver : complete insmod
PL080 DMAC Driver : IRQ 8
PCIeDMAC Driver : irq_no 10
### pccregdrv ### <7>pccreg_cdev_init
smac: eth0: smac_reset: hw tx done
smac: eth0: smac_reset: sw reset done
smac: eth0: smac_open: smac version: 0.0.2-NAPI-JUMBO
smac: eth0: smac_open: hw version: 0.5.11.23
smac: eth0: smac_request_irq: irq:2
ADDRCONF(NETDEV_UP): eth0: link is not ready
smac: eth0: smac_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
ssp: requested write byte 2
ssp: TX in rp:0 wp:1
ssp: Write FIFO 1 times : max_count: 1
ssp: TX out rp:1 wp:1
ssp: actual write byte 2
sdif_driver : sdif_block_open
sdif_driver : SDIF_Card_MemoryOpen = 7
eth0: no IPv6 routers present
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
это все с Apix-VDome/M1 3312
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
на Box/M1 все идентично
Re: глюки с Evidence Apix-Box/M1 и Apix-VDome/M1 3312
Сделайте бэкап и потом по-очереди убивайте все разделы подозрительные. начиная с 16. А еще лучше найти такую же живую, снять дамп и залить на все мертвые.
