Видеорегистратор SVR-4425 AH, нужна помощь.

[anmik]

Видеорегистратор Satvision SVR-4425 AH. Повреждена прошивка. При включении регистратора на экране появляется логотип и после этого темный экран.Ниже лог загрузки. Скачал прошивку с сайта. Дамп с флешки тоже снял. Не пойму, как залить скачанную прошивку. Подтолкните в нужном направлении если не трудно.

[anmik]

Лог загрузки:
U-Boot 2010.06 (Jun 21 2013 - 11:45:11)

Check spi flash controller v350... Found
Spi(cs1) ID: 0x01 0x20 0x18 0x03 0x01 0x00
Spi(cs1): Block:64KB Chip:16MB Name:"S25FL128P-1"
In: serial
Out: serial
Err: serial
current hi352xx version 201306211132
current used inner phy
current used 256M mem
current used param offset 11111111111111111
current do_check_flash_boot_param
current prod net 100m
init gpio led setting
dev 0 set background color!
dev 2 set background color!
dev 0 opened!
dev 2 opened!
jpeg decoding ...
<<addr=0x80080000, size=0x6514, vobuf=0x8fd00000>>
mmu_enable
<<imgwidth=480, imgheight=320, linebytes=960>>
decode success!!!!
dev 0 set background color!
dev 2 set background color!
dev 0 opened!
vo hd 0 end
dev 2 opened!
vo cvbs end
graphic layer 0 opened!
graphic layer 2 opened!
USB: scanning bus for devices... 1 USB Device(s) found
0 Storage Device(s) found
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.0.8
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2285288 Bytes = 2.2 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (lzg@localhost.localdomain) (gcc version 4.4.1

(Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #15 Wed Aug 21 11:10:56 CST 2013
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: hi3520d
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 19812
Kernel command line: mem=78M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=jffs2

mtdparts=hi_sfc:768K(boot),2304K(dva110000),13M(rootfs)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 78MB = 78MB total
Memory: 74496k/74496k available, 5376k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc5000000 - 0xfe000000 ( 912 MB)
lowmem : 0xc0000000 - 0xc4e00000 ( 78 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0029000 ( 132 kB)
.text : 0xc0029000 - 0xc040f000 (3992 kB)
.data : 0xc0410000 - 0xc042e200 ( 121 kB)
.bss : 0xc042e224 - 0xc047bd80 ( 311 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 82MHz, resolution 12ns, wraps every 52060ms
Console: colour dummy device 80x30
Calibrating delay loop... 1318.91 BogoMIPS (lpj=6594560)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
L2cache cache controller enabled
JFFS2 version 2.2. (NAND) В© 2001-2006 Red Hat, Inc.
fuse init (API version 7.16)
msgmni has been set to 145
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
ahci: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl platform mode
ahci ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc sxs boh
scsi0 : ahci_platform
scsi1 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x100 irq 52
ata2: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x180 irq 52
Spi id table Version 1.22
Spi(cs1) ID: 0x01 0x20 0x18 0x03 0x01 0x00
SPI FLASH start_up_mode is 3 Bytes
Spi(cs1):
Block:64KB
Chip:16MB
Name:"S25FL128P-1"
spi size: 0x16777216
chip num: 1
3 cmdlinepart partitions found on MTD device hi_sfc
Creating 3 MTD partitions on "hi_sfc":
0x000000000000-0x0000000c0000 : "boot"
0x0000000c0000-0x000000300000 : "dva110000"
0x000000300000-0x000001000000 : "rootfs"
Fixed MDIO Bus: probed
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 53, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 54, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
registered taskstats version 1
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
VFS: Mounted root (jffs2 filesystem) on device 31:2.
Freeing init memory: 132K

_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
Jan 1 00:00:03 udevd (467): /proc/467/oom_adj is deprecated, please use /proc/467/oom_score_adj instead.
udevd[467]: main: error opening /dev/null: No such file or directory

[RCS]: /etc/init.d/S80network
[RCS]: /etc/init.d/S81toe
No need to recovery program from USB
clkcfg_hi3520D.sh
crgctrl_1X1080P_hi3520D.sh
crgctrl_1XHD_4XD1_hi3520D.sh
crgctrl_2X720P_hi3520D.sh
crgctrl_8D1_hi3520D.sh
extdrv/
extdrv/sunrpc.ko
extdrv/nvp6124.ko
extdrv/wdt.ko
extdrv/mv88e6071.ko
extdrv/nvp6114_ex.ko
extdrv/nvp1918.ko
extdrv/hieth_switch.ko
extdrv/rt5616.ko
extdrv/hieth.ko
extdrv/lockd.ko
extdrv/crypto_memory.ko
extdrv/hi_ir.ko
extdrv/gpioi2c.ko
extdrv/nfs.ko
extdrv/auth_rpcgss.ko
extdrv/gpio2x_sh4101b.ko
extdrv/hi_rtc.ko
extdrv/ssp.ko
extdrv/nfs_acl.ko
extdrv/net-pnp.ko
extdrv/fgpio.ko
hi3520D_adec.ko
hi3520D_aenc.ko
hi3520D_ai.ko
hi3520D_ao.ko
hi3520D_base.ko
hi3520D_chnl.ko
hi3520D_dsu.ko
hi3520D_group.ko
hi3520D_h264e.ko
hi3520D_hdmi.ko
hi3520D_ive.ko
hi3520D_jpege.ko
hi3520D_rc.ko
hi3520D_region.ko
hi3520D_sio.ko
hi3520D_sys.ko
hi3520D_tde.ko
hi3520D_vda.ko
hi3520D_vdec.ko
hi3520D_venc.ko
hi3520D_vfmw.ko
hi3520D_viu.ko
hi3520D_vou.ko
hi3520D_vpss.ko
hifb.ko
hi_rtc.ko
hiuser.ko
jpeg.ko
load3520D
load3520D_socket
mmz.ko
pinmux_8D1_hi3520D.sh
sysctl_hi3520D_4x720P.sh
sysctl_hi3520D.sh
vcmp.ko
SDK_TYPE type is 8d1
Hisilicon Media Memory Zone Manager
Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 1)
current 3520d watchdog version 201304181021
hi3520D_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
load sys.ko ...OK!
Load tde.ko ...OK!
load venc.ko ...OK!
load group.ko ...OK!
load chnl.ko ...OK!
load h264e.ko ...OK!
load rc.ko ...OK!
load jpege.ko ...OK!
load viu.ko ...OK!
load vou.ko ....OK!
load vpss.ko ....OK!
load vda.ko ....OK!
load region.ko ....OK!
load vdec.ko ....OK
load vhd firmware.ko OK
load hdmi.ko ....OK!
Load jpeg6b.ko success. (SDK_VERSION:[jpeg6bv1.0] Build Time:[Sep 29 2014, 18:04:52])
i2c 3520d version : 201304181021
current chip numbers = 0
insmod: can't insert 'extdrv/nvp1918.ko': Operation not permitted
keybaord 3520d gpio init version : 201304181021
HISI_IRDA-MF @Hi3520Dv100R00
hiir: init ok. 3520d ver 201304181021 =Apr 18 2013, 11:27:01.
current 3520d ver 201309091128 rtc
version - 3520d :201310190913+->TD3515
TVT 3520d CryptoMemory Device Driver v1.0.0: Oct 19 2013 09:28:46
nvp6114 Device ID Error... ff 10
nvp6114 Device ID Error... ff 10
nvp6114 Device ID Error... ff 10
nvp6114 Device ID Error... ff 10
nvp6114 not exist ++++SSSS++++
insmod: can't insert 'extdrv/nvp6114_ex.ko': Operation not permitted
rt5616 not exist ++++SSSS++++
insmod: can't insert 'extdrv/rt5616.ko': Operation not permitted
nvp6124 Device (0x60) ID OK... 85
NVP6124 Driver Ver030 2015.09.16-18:20(compile-time Sep 16 2015 18:21:04)
current net is not poe
current sys kernel has not config net
himii: probed
Invalid HW-MAC Address: 00:00:00:00:00:00
Set Random MAC address: A6:7C:48:09:0B:D5
hieth_init ok version is 20150205
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Arabic/
Arabic/WebKit_load.xml
Arabic/cfg_ptz_advance.xml
Arabic/cfg_net_stream.xml
Arabic/cfg_ptz.xml
Arabic/cfg_record_stream.xml
Arabic/cfg_rec_snap.xml
Arabic/cfg_rec_osd.xml
Arabic/cfg_record.xml
Arabic/info_net.xml
Arabic/time_search.xml
Arabic/cfg_motion_area.xml
Arabic/backup.xml
Arabic/cfg_net_mail.xml
Arabic/cfg_schedule.xml
Arabic/cfg_advance_ban.xml
Arabic/cfg_net_autoreport.xml
Arabic/cfg_basic.xml
Arabic/search_nav.xml
Arabic/cfg_net_nat_autoreport.xml
Arabic/advance.xml
Arabic/cfg_track_set.xml
Arabic/cfg_device.xml
Arabic/playback.xml
Arabic/live.xml
Arabic/info_online.xml
Arabic/info_event.xml
Arabic/cfg_alarmout.xml
Arabic/cfg_net_wireless.xml
Arabic/cfg_motion_alarm.xml
Arabic/WebKit_update.xml
Arabic/cfg_live.xml
Arabic/cfg_net_ftp.xml
Arabic/main_menu.xml
Arabic/cfg_net.xml
Arabic/cfg_index.xml
Arabic/cfg_user.xml
Arabic/info_basic.xml
Arabic/cfg_other_alarm.xml
Arabic/info_log.xml
Arabic/login.xml
Arabic/file_manage.xml
Arabic/cfg_sensor_alarm.xml
Arabic/cfg_vloss_alarm.xml
Arabic/cfg_local.xml
Arabic/cfg_preset_set.xml
Arabic/cfg_advance.xml
Arabic/info_index.xml
Arabic/event_search.xml
Arabic/string.js
bulgarian/
bulgarian/WebKit_load.xml
bulgarian/cfg_ptz_advance.xml
bulgarian/cfg_net_stream.xml
bulgarian/cfg_ptz.xml
bulgarian/cfg_record_stream.xml
bulgarian/cfg_rec_snap.xml
bulgarian/cfg_rec_osd.xml
bulgarian/manual_alarm.xml
bulgarian/cfg_record.xml
bulgarian/info_net.xml
bulgarian/time_search.xml
bulgarian/cfg_motion_area.xml
bulgarian/backup.xml
bulgarian/cfg_net_mail.xml
bulgarian/cfg_schedule.xml
bulgarian/cfg_advance_ban.xml
bulgarian/cfg_net_autoreport.xml
bulgarian/cfg_basic.xml
bulgarian/search_nav.xml
bulgarian/cfg_net_nat_autoreport.xml
bulgarian/advance.xml
bulgarian/cfg_track_set.xml
bulgarian/cfg_device.xml
bulgarian/playback.xml
bulgarian/live.xml
bulgarian/info_online.xml
bulgarian/info_event.xml
bulgarian/cfg_alarmout.xml
bulgarian/cfg_net_wireless.xml
bulgarian/cfg_motion_alarm.xml
bulgarian/WebKit_update.xml
bulgarian/cfg_live.xml
bulgarian/cfg_net_ftp.xml
bulgarian/main_menu.xml
bulgarian/cfg_net.xml
bulgarian/cfg_index.xml
bulgarian/cfg_user.xml
bulgarian/info_basic.xml
bulgarian/cfg_other_alarm.xml
bulgarian/info_log.xml
bulgarian/login.xml
bulgarian/file_manage.xml
bulgarian/cfg_sensor_alarm.xml
bulgarian/cfg_vloss_alarm.xml
bulgarian/cfg_local.xml
bulgarian/cfg_preset_set.xml
bulgarian/cfg_advance.xml
bulgarian/info_index.xml
bulgarian/event_search.xml
bulgarian/string.js
chinese_cht/
chinese_cht/WebKit_load.xml
chinese_cht/cfg_ptz_advance.xml
chinese_cht/cfg_net_stream.xml
chinese_cht/cfg_ptz.xml
chinese_cht/cfg_record_stream.xml
chinese_cht/cfg_rec_snap.xml

---------------------------------------------------------------------------------------------------

vietnamese/cfg_net_wireless.xml
vietnamese/cfg_motion_alarm.xml
vietnamese/WebKit_update.xml
vietnamese/cfg_live.xml
vietnamese/cfg_net_ftp.xml
vietnamese/main_menu.xml
vietnamese/cfg_net.xml
vietnamese/cfg_index.xml
vietnamese/cfg_user.xml
vietnamese/info_basic.xml
vietnamese/cfg_other_alarm.xml
vietnamese/info_log.xml
vietnamese/login.xml
vietnamese/file_manage.xml
vietnamese/cfg_sensor_alarm.xml
vietnamese/cfg_vloss_alarm.xml
vietnamese/cfg_local.xml
vietnamese/cfg_preset_set.xml
vietnamese/cfg_advance.xml
vietnamese/info_index.xml
vietnamese/event_search.xml
vietnamese/string.js
arabic.dat
bulgarian.dat
chinese_b.dat
chinese_s.dat
czech.dat
dutch.dat
english.dat
french.dat
german.dat
greece.dat
hebrew.dat
hungary.dat
indonesia.dat
italy.dat
japanese.dat
lithuania.dat
norway.dat
persian.dat
polish.dat
portuguese.dat
romanian.dat
russian.dat
spaish.dat
swedish.dat
thai.dat
turkey.dat
vietnamese.dat
cp: can't stat '/mnt/mtd/libApiNetSocket.so.lzma': No such file or directory
cp: can't stat '/mnt/mtd/libApiServer.so.lzma': No such file or directory
cp: can't stat '/mnt/mtd/libApiShareLib.so.lzma': No such file or directory
cp: can't stat '/mnt/mtd/libApiuuid.so.lzma': No such file or directory
unlzma: libApiNetSocket.so.lzma: No such file or directory
unlzma: libApiServer.so.lzma: No such file or directory
unlzma: libApiShareLib.so.lzma: No such file or directory
unlzma: libApiuuid.so.lzma: No such file or directory
ln: /mnt/mtd/mkisofs: File exists
ln: /mnt/mtd/growisofs: File exists
rm: can't remove '/mnt/mtd/preupgrade.sh': No such file or directory
rm: can't remove '/mnt/mtd/productcheck': No such file or directory
current net is not poe
ADDRCONF(NETDEV_UP): eth0: link is not ready
ln: /mnt/mtd/WebServer/logo: File exists
cp: can't stat '/mnt/udhcpd.delta': No such file or directory
cp: can't stat '/mnt/udhcpd0.leases': No such file or directory
Auto login as root ...
(none) login: xdvr.cpp, 706, pid = 897, tid=897
PUB_common.cpp, 1934, pid = 897, tid=898
check OK!
read xyz vlaue *=* 10725
eth0 MAC Address 00:18:ae:5c:76:bc
------get 1------current param type == 4085
------get 1------current param type == 4086
read cry ok and the mac:0018ae5c76bc and cry is not change
product_id = 10725
LocalDevice.cpp,4630,new crytoinfo
#############xdvr.cpp,730,productID:10725
productID:10725,subProductID:0
xdvr.cpp,751,programeId:0,subProductID:0.xdvr.cpp,796,g_bProIdequeSubProdID:1
######################xdvr.cpp,815,no change CVBS Resolution
hdtype=0
GetVideoFormatFromFlash:LocalDevice.cpp:4350, Get video format from flash
current flash param ==
------get 1------current param type == 4069
------get 1------current param type == 4066
product Item (Product.cpp,463)from programe
------get 1------current param type == 4068
------get 1------current param type == 4073
Product.cpp,29736,info.function[FUNC_NO_ALARM_CTRL/bitCount]:fc9dffc
------get 1------current param type == 4072
------get 1------current param type == 4071
LocalDevice.cpp,4580,GetKeyBoardNameFromFlash:Q23
xdvr.cpp,880,ChangeKeyBoardType keyboardType:0
xdvr.cpp,893,local keyboardtype;0
Intial CLanguagePack succ!
------get 1------current param type == 4070
Initial ReadDDdns ok
Inital config manager succ
ConfigEx.cpp,2398, first check NCFG_ITEM_ENCODE_MAJOR maxRate:500,totalRate:800
ConfigEx.cpp,2402, no need change NCFG_ITEM_ENCODE_MAJOR
CVBS_ChangeParam********************************************************
##xdvr.cpp,1298,videoout res flash == config
main:xdvr.cpp:1483, videoPbChnnNum=0x00000004
AdjustCVBSVo:LocalDevice.cpp:5089, dislW=720, dispH=576
change cvbs output size 720,576
pFrameRateData ----------------- 0,0
sdk set cvbs support
current product used chip *****++++ HISI3520D ++++*****
------get 1------current param type == 4083
------get 1------current param type == 4084
current read param in kernel version 0 = 51c3cc81, 1 = 52142fdf, 2 = 55dfbd0e
DVR SDK VERSION : *** Oct 13 2015 16:54:08 ***
DVR SDK VERSION : *** 201510081032 ***
current alloc buf variant len = 195584
alloc frame queue cnt 50,4,1155000
current jiffts value = 100
****----TD2704AS-SL dvr sub version = 0
alloc m_pb_buf_addr = 40e9f008, 1835008
alloc m_compress_buf_addr 41061008, 10747904
all used mem len 12918784
------get 1------current param type == 4066
current hardware version : DALAH len : 5
current keyboard +++++++ type 1, get pos 8
mcusim run_prog_pos = 6, alarm 0,0, spot 0, buzzer 0
current product 3515 keyboard se 0
current jpeg set vale = 1

alloc var buffer add 400d8008, len 330960, PCIV_FONT_DOT_PARAM = 2400
alloc mem font param 22714,32,726848
Current TD2704AS_SL DVR Product Param Init == sub ver 0
current decode chip number = 1
open /dev/rt5616_dev failed
--open /dev/nvp6114dev failed
open /dev/nvp6124 success
nvp6114a_outport_1mux_chseq


6124_mode_setting_ch[0] change 0xff to 0x3



6124_mode_setting_ch[1] change 0xff to 0x3



6124_mode_setting_ch[2] change 0xff to 0x3



6124_mode_setting_ch[3] change 0xff to 0x3

NVP6124_AfeReset done

[IOC_VDEC_SET_VIDEO_MODE]::hardware==255 mode==2 product==1::

nvp6114a_set_portmode chip 0 portsel 0 portmode 7 setting
nvp6114a_set_portmode chip 0 portsel 1 portmode 7 setting
start vi vo device ......
current chip workmode = 9999
ViMsk=3,VoMsk=1,b_pal=1 b_vag_mod=0,b_cpu_slave=0
b_cascade_master=0,b_used_pip=1,iWorkMode=9999,vo_img_width=1920,vo_img_height=1080
product_type=2704206,flag_dec_mem_is_used_pip=0,flag_dec_mem_is_used_doublefrm=0
hdmi start force mode =-----------> HI_HDMI_FORCE_HDMI
HDMI start success.
init channel param ----------
start vi channel ......
mode bgc enable no interrup detect ==== ViChn 4
mode bgc enable no interrup detect ==== ViChn 6
mode bgc enable no interrup detect ==== ViChn 0
mode bgc enable no interrup detect ==== ViChn 2
start venc group ......
start venc net group .....
start venc local ......
start venc net ......
change venc 16 rc param
change venc 17 rc param
change venc 18 rc param
change venc 19 rc param
start vdec ......
current vdec 0 display buf num 2
current vdec 1 display buf num 2
current vdec 2 display buf num 2
current vdec 3 display buf num 2
start cascade vi ......
start tde ......
start framebuf G0 ......
current set fb width 1920, height 1080
fb width 1920, height 1080, len 8294400, 3840
start framebuf HC0 ......
current set fb width 32, height 32
fb width 32, height 32, len 4096, 128
get current color 0 val 50, color martix 1
get current color 1 val 50, color martix 1
get current color 2 val 50, color martix 1
get current color 3 val 59, color martix 1
sdvr initialize success
AEC_Init error framelen(320)
[Func]:MPI_AI_AecInit [Line]:369 [Info]:aec open fail.
LocalDevice.cpp,208,ext_device_init
current rtc time (0) 15,10,17,11,20,23
RTC Time:15-10-17 11:20:23
##read chip type:28673 is other chip
###LocalDevice.cpp,344,485CS
####################3LocalDevice.cpp,358 CLocalDevice::Initial
,Initial local device succ!
fb w = 1920, h = 1080
The mem is :4147200
The line_length is :3840
The xres is :1920
The yres is :1080
bits_per_pixel is :16
thread_route_encode_video_net_device, thread id = 913
thread_vedio_type_check, thread id = 912
thread_route_audio_capture, thread id = 914
thread_vedio_loss_check, thread id = 911
thread_route_video_playbck, thread id = 915
thread_route_video_pb_local, thread id = 916
thread_route_encode_video_local_device, thread id = 910
thread_route_audio_playback, thread id = 917
thread_route_vda_md, thread id = 918
thread_route_check_other_thread, thread id = 919
thread_route_encode_video_frame, thread id = 909
thread_route_mouse_process, thread id = 920
thread_route_keyboard_process, thread id = 921
thread_route_ir_process, thread id = 922
thread_route_feed_wdg, thread id = 923
thread_route_capture_jpeg, thread id = 924
thread_route_slave_cpu_check_time, thread id = 925
insert master vi chn 4 0 user pic int:0 lost:0 u32ChnFrmRate = 0
advance.bmp
advance_f.bmp
alarm.bmp
alarm_f.bmp
alarm_out.bmp
alarm_out_f.bmp
all.bmp
all_f.bmp
anchor_cam_para.bmp
anchor_cam_para_f.bmp
anchor_roi.bmp
anchor_roi_f.bmp
arrow_left.bmp
arrow_left_f.bmp
backup.bmp
backup_copy.bmp
backup_copy_f.bmp
backup_copy_n.bmp
backup_f.bmp
basic_config.bmp
basic_config_f.bmp
btn_add.bmp
btn_add_f.bmp
btn.bmp
btn_bottom.bmp
btn_bottom_f.bmp
btn_dec.bmp
btn_dec_f.bmp
btn_del.bmp
btn_del_f.bmp
btn_down.bmp
btn_down_f.bmp
btn_f.bmp
btn_modify.bmp
btn_modify_f.bmp
btn_top.bmp
btn_top_f.bmp
btn_up.bmp
btn_up_f.bmp
check.bmp
check_f.bmp
check_n.bmp
check_no.bmp
check_no_f.bmp
check_no_n.bmp
clear.bmp
clear_f.bmp
combo_btn_down.bmp
combo_btn_down_f.bmp
combo_btn_down_n.bmp
combo_btn_left.bmp
combo_btn_left_f.bmp
combo_btn_left_n.bmp
combo_btn_right.bmp
combo_btn_right_f.bmp
combo_btn_right_n.bmp
config.bmp
config_f.bmp
custom.bmp
custom_f.bmp
cut_end.bmp
cut_end_f.bmp
cut_end_n.bmp
cut_start.bmp
cut_start_f.bmp
cut_start_n.bmp
date_btn_calendar.bmp
date_btn_calendar_f.bmp
device.bmp
device_f.bmp
dialog.bmp
dialog_child.bmp
disk.bmp
disk_f.bmp
dlg_flex_l.bmp
dlg_flex_l_f.bmp
dlg_flex_r.bmp
dlg_flex_r_f.bmp
edit.bmp
edit_f.bmp
erase.bmp
erase_f.bmp
error.bmp
event.bmp
event_f.bmp
exit2.bmp
exit2_f.bmp
exit3.bmp
exit3_f.bmp
exit4.bmp
exit4_f.bmp
exit.bmp
exit_f.bmp
fast_forward.bmp
fast_forward_f.bmp
fast_forward_n.bmp
font.dat
goto.bmp
goto_f.bmp
icon_cfg_blacklist.bmp
icon_cfg_man.bmp
icon_cfg_reset.bmp
icon_exit.bmp
icon_info.bmp
info.bmp
info_f.bmp
listex_btn_left.bmp
listex_btn_left_f.bmp
listex_btn_leftmost.bmp
listex_btn_leftmost_f.bmp
listex_btn_right.bmp
listex_btn_rightmost.bmp
listex_btn_rightmost_f.bmp
listex_right_f.bmp
list_header.bmp
live_audio.bmp
live.bmp
live_f.bmp
live_motion_big.bmp
live_motion.bmp
live_ptz.bmp
live_snap_tip.bmp
live_snap_tip_fail.bmp
lock.bmp
log.bmp
log_f.bmp
logoff.bmp
logoff_f.bmp
manual_alarm.bmp
manual_alarm_f.bmp
mini_map.bmp
mini_map_f.bmp
motion.bmp
motion_f.bmp
network.bmp
network_f.bmp
next_frame.bmp
next_frame_f.bmp
next_frame_n.bmp
next_section.bmp
next_section_f.bmp
ok.bmp
ok_f.bmp
online_user.bmp
online_user_f.bmp
other_alarm.bmp
other_alarm_f.bmp
pause.bmp
pause_f.bmp
pause_n.bmp
pen.bmp
pen_f.bmp
play_1a12.bmp
play_1a12_f.bmp
play_1a12_n.bmp
play_1a5.bmp
play_1a5_f.bmp
play_1a5_n.bmp
play_1a7.bmp
play_1a7_f.bmp
play_1a7_n.bmp
play_1x1.bmp
play_1x1_f.bmp
play_1x1_n.bmp
play_2x2.bmp
play_2x2_f.bmp
play_2x2_n.bmp
play_2x3.bmp
play_2x3_f.bmp
play_2x3_n.bmp
play_3x3.bmp
play_3x3_f.bmp
play_3x3_n.bmp
play_4x4.bmp
play_4x4_f.bmp
play_4x4_n.bmp
play_audio.bmp
play_audio_f.bmp
play_audio_m.bmp
play_audio_m_f.bmp
play_audio_n.bmp
play_bg.bmp
play.bmp
player_hide.bmp
player_hide_f.bmp
play_f.bmp
play_live.bmp
play_live_f.bmp
play_live_n.bmp
play_move.bmp
play_move_f.bmp
play_n.bmp
play_triangle.bmp
play_triangle_f.bmp
play_zoom.bmp
play_zoom_f.bmp
play_zoom_n.bmp
pop_split.bmp
pop_split_f.bmp
pop_split_n.bmp
prev_section.bmp
prev_section_f.bmp
progress1.bmp
progress2.bmp
progress_n.bmp
ptz.bmp
ptz_brush_off.bmp
ptz_brush_off_f.bmp
ptz_brush_on.bmp
ptz_brush_on_f.bmp
ptz_ctrl_bk.bmp
ptz_down.bmp
ptz_down_f.bmp
ptz_down_left.bmp
ptz_down_left_f.bmp
ptz_down_right.bmp
ptz_down_right_f.bmp
ptz_f.bmp
ptz_lamp_off.bmp
ptz_lamp_off_f.bmp
ptz_lamp_on.bmp
ptz_lamp_on_f.bmp
ptz_left.bmp
ptz_left_f.bmp
ptz_right.bmp
ptz_right_f.bmp
ptz_stop.bmp
ptz_stop_f.bmp
ptz_up.bmp
ptz_up_f.bmp
ptz_up_left.bmp
ptz_up_left_f.bmp
ptz_up_right.bmp
ptz_up_right_f.bmp
qrcode.bmp
qrcode_f.bmp
question.bmp
radio.bmp
radio_f.bmp
radio_n.bmp
radio_no.bmp
radio_no_f.bmp
radio_no_n.bmp
record.bmp
record_f.bmp
resources.bmp
resources_f.bmp
reward.bmp
reward_f.bmp
reward_n.bmp
save.bmp
save_f.bmp
schedule.bmp
schedule_f.bmp
scroll_bottom.bmp
scroll_bottom_f.bmp
scroll_btn.bmp
scroll_btn_f.bmp
scroll_btn_v.bmp
scroll_btn_v_f.bmp
scroll_left.bmp
scroll_left_f.bmp
scroll_right.bmp
scroll_right_f.bmp
scroll_top.bmp
scroll_top_f.bmp
search_1x1.bmp
search_1x1_f.bmp
search_1x1_n.bmp
search_1x1_sel.bmp
search_2x2.bmp
search_2x2_f.bmp
search_2x2_n.bmp
search_2x2_sel.bmp
search_2x3.bmp
search_2x3_f.bmp
search_2x3_n.bmp
search_2x3_sel.bmp
search_3x3.bmp
search_3x3_f.bmp
search_3x3_n.bmp
search_3x3_sel.bmp
search_4x4.bmp
search_4x4_f.bmp
search_4x4_n.bmp
search_4x4_sel.bmp
search.bmp
search_f.bmp
search_play.bmp
search_play_f.bmp
sensor.bmp
sensor_f.bmp
set_color.bmp
set_color_f.bmp
set_color_n.bmp
shutdown.bmp
shutdown_f.bmp
Slider_bk.bmp
Slider_box.bmp
Slider_box_f.bmp
Slider_box_n.bmp
Slider_box_v.bmp
Slider_box_v_f.bmp
snap.bmp
snap_f.bmp
snap_n.bmp
stop.bmp
stop_f.bmp
stop_n.bmp
system.bmp
system_f.bmp
tab.bmp
tab_check.bmp
tab_f.bmp
tip_info.bmp
tool_1a12.bmp
tool_1a12_f.bmp
tool_1a5.bmp
tool_1a5_f.bmp
tool_1a7.bmp
tool_1a7_f.bmp
tool_1x1.bmp
tool_1x1_f.bmp
tool_2x2.bmp
tool_2x2_f.bmp
tool_2x3.bmp
tool_2x3_f.bmp
tool_3x3.bmp
tool_3x3_f.bmp
tool_4x4.bmp
tool_4x4_f.bmp
insert master vi chn 6 0 user pic int:0 lost:0 u32ChnFrmRate = 0
tool_5x5.bmp
tool_5x5_f.bmp
tool_6x6.bmp
tool_6x6_f.bmp
tool_arm.bmp
tool_arm_f.bmp
tool_audio.bmp
tool_audio_f.bmp
tool_audio_mute.bmp
tool_audio_mute_f.bmp
toolbar.bmp
tool_dwell.bmp
tool_dwell_f.bmp
tool_dwell_no.bmp
tool_dwell_no_f.bmp
tool_edit.bmp
tool_edit_f.bmp
tool_hide.bmp
tool_hide_f.bmp
tool_menu.bmp
tool_menu_f.bmp
tool_pip.bmp
tool_pip_f.bmp
tool_play.bmp
tool_play_f.bmp
tool_ptz.bmp
tool_ptz_f.bmp
tool_rec.bmp
tool_rec_f.bmp
tool_set_cam_para.bmp
tool_set_cam_para_f.bmp
tool_set_color.bmp
tool_set_color_f.bmp
tool_snap.bmp
tool_snap_f.bmp
tool_sysinfo.bmp
tool_sysinfo_f.bmp
tool_triangle.bmp
tool_triangle_f.bmp
tool_winedit.bmp
tool_winedit_f.bmp
tool_zoom.bmp
tool_zoom_f.bmp
user.bmp
user_f.bmp
videoloss.bmp
videoloss_f.bmp
waitting.bmp
warning.bmp
insert master vi chn 0 0 user pic int:0 lost:0 u32ChnFrmRate = 0
insert master vi chn 2 0 user pic int:0 lost:0 u32ChnFrmRate = 0
Start flash screen ok!
------get 1------current param type == 4065
xdvr.cpp, 465, pid = 897, tid = 942 start flash screen.
macflash:00:18:AE:5C:76:BC MAC=30303a31383a41453a35433a37363a4243
macfile:00:18:AE:5C:76:BC MAC=30303a31383a41453a35433a37363a4243
bRestartForCheckMac:xdvr.cpp:358, running at here, lenFile=17, lenFlash=17
videoflash:1
videofile:1
------get 1------current param type == 4075
Initial message man succ
cur language is in language list
arabic.dat
bulgarian.dat
chinese_b.dat
chinese_s.dat
czech.dat
dutch.dat
english.dat
french.dat
german.dat
greece.dat
hebrew.dat
hungary.dat
indonesia.dat
italy.dat
japanese.dat
lithuania.dat
norway.dat
persian.dat
polish.dat
portuguese.dat
romanian.dat
russian.dat
spaish.dat
swedish.dat
thai.dat
turkey.dat
vietnamese.dat
tempWirelesscfg.enable=========0
MainFrame.cpp,11089,start dog
MainFrame.cpp,11119,set chnn:0, waterMack
MainFrame.cpp,11119,set chnn:1, waterMack
MainFrame.cpp,11119,set chnn:2, waterMack
MainFrame.cpp,11119,set chnn:3, waterMack
MainFrame.cpp,11122,kill dog
Setup warter mark
CDOperationMan.cpp,63
Initial CD-Rom man succ
dvrId:0018ae5c76bc0000
Initial diskmanager succ
Initial reclog manager succ
Initial log manager succ
Inital liveStreamRecord manager succ
Inital record manager succ
Initial smtp manager succ
Initial m_pSnapPictureMan manager succ
Inital stream proc succ
Inital data server proc succ
Inital netReader succ
Initial backupman succ
Initial smtp manager succ
Initial alarm out manager succ
Initial motion manager succ
Initial sensor in manager succ
Initial video loss manager succ
Initial video loss manager succ
Initial alarm manager succ
Initial ptz manager succ
Initial fake curise succ
Initial pinyin input succ
Initial display man succ
Initial UpnpMan man succ
Initial config set manager succ
Initial:MainFrame.cpp:935, my mac=0018ae5c76bc
get the str = 000-494e
Initial():MainFrame.cpp:958, initial the alloc NIC IP succ
Initial():MainFrame.cpp:982, initial the DDNS manager succ
LocalTimeSYNNTPServer:TZoneDZoneCfg.cpp:171, stop to syn to the ntp server
ReclogManEx.cpp,1214,diskSize:128
@@@@@@ConfigSetMan.cpp,840, Initial CMessageMan::Instance()->SetChannelVisible:1
@@@@@@ConfigSetMan.cpp,841, Initial m_pLocalDeviceMan->SetCamVisible:1
AdjustCVBSVo:LocalDevice.cpp:5089, dislW=720, dispH=576
change cvbs output size 720,576
cur setting cvbs out image size 720,576
Action false NetReader.cpp 124
2 ConfigSetMan.cpp,982,GMT0BST,M3.5.0/1,M10.5.0
ConfigSetMan.cpp,3351,NCFG_ITEM_JPEG_PERIOD:2
ConfigSetMan.cpp,3358,NCFG_ITEM_JPEG_SIZE:2
ConfigSetMan.cpp,3388,NCFG_ITEM_JPEG_QUALITY:4 ==> 3
ConfigSetMan.cpp,3396,NCFG_ITEM_JPEG_SNAP_NUM:3
########SmtpMan.cpp,535,m_snapImgNum:3
SetVideoSize:LocalDevice.cpp:2441, set chnn:00 local video size:32
SetFrameRateQuality:LocalDevice.cpp:2554, set chnn:00 local rate:25, encode:2, bitstream:4096, quality:5
SetVideoSize:LocalDevice.cpp:2441, set chnn:01 local video size:32
SetFrameRateQuality:LocalDevice.cpp:2554, set chnn:01 local rate:25, encode:2, bitstream:4096, quality:5
SetVideoSize:LocalDevice.cpp:2441, set chnn:02 local video size:64
SetFrameRateQuality:LocalDevice.cpp:2554, set chnn:02 local rate:25, encode:2, bitstream:2048, quality:5
SetVideoSize:LocalDevice.cpp:2441, set chnn:03 local video size:64
SetFrameRateQuality:LocalDevice.cpp:2554, set chnn:03 local rate:25, encode:2, bitstream:2048, quality:5
route: SIOCADDRT: File exists
CMD : route add -net 224.0.0.0 netmask 240.0.0.0 dev eth0 execute fail
td3520d invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0, oom_score_adj=0
Backtrace:
[<c0033bf0>] (dump_backtrace+0x0/0x110) from [<c0345470>] (dump_stack+0x18/0x1c)
r6:00000261 r5:00000000 r4:c4adc5c0 r3:60000113
[<c0345458>] (dump_stack+0x0/0x1c) from [<c007b9cc>] (T.374+0x58/0x154)
[<c007b974>] (T.374+0x0/0x154) from [<c007bb4c>] (T.373+0x84/0x234)
[<c007bac8>] (T.373+0x0/0x234) from [<c007bf38>] (out_of_memory+0x23c/0x2f8)
[<c007bcfc>] (out_of_memory+0x0/0x2f8) from [<c0080c2c>] (__alloc_pages_nodemask+0x5f0/0x604)
[<c008063c>] (__alloc_pages_nodemask+0x0/0x604) from [<c0079538>] (filemap_fault+0x180/0x404)
[<c00793b8>] (filemap_fault+0x0/0x404) from [<c0091994>] (__do_fault+0x5c/0x428)
[<c0091938>] (__do_fault+0x0/0x428) from [<c0092034>] (handle_pte_fault+0x7c/0xa48)
[<c0091fb8>] (handle_pte_fault+0x0/0xa48) from [<c0092e40>] (handle_mm_fault+0x94/0xc0)
[<c0092dac>] (handle_mm_fault+0x0/0xc0) from [<c0036bb0>] (do_page_fault+0x170/0x1e4)
[<c0036a40>] (do_page_fault+0x0/0x1e4) from [<c0029204>] (do_PrefetchAbort+0x40/0xa4)
[<c00291c4>] (do_PrefetchAbort+0x0/0xa4) from [<c002ffa4>] (ret_from_exception+0x0/0x10)
Exception stack(0xc25a3fb0 to 0xc25a3ff8)
3fa0: 00000000 00000000 4b163504 00000000
3fc0: 00000000 00000000 4b162e68 000000a2 00000002 00000000 40138d4c 4b162fe4
3fe0: 40583ccc 4b162e50 404fe628 404fe5b8 80000010 ffffffff
r7:000000a2 r6:4b162e68 r5:00000000 r4:ffffffff
Mem-info:
Normal per-cpu:
CPU 0: hi: 18, btch: 3 usd: 13
active_anon:11842 inactive_anon:2194 isolated_anon:0
active_file:0 inactive_file:2 isolated_file:12
unevictable:0 dirty:0 writeback:0 unstable:0
free:553 slab_reclaimable:105 slab_unreclaimable:1872
mapped:126 shmem:2196 pagetables:96 bounce:0
Normal free:2212kB min:2048kB low:2560kB high:3072kB active_anon:47368kB inactive_anon:8776kB active_file:0kB

inactive_file:8kB unevictable:0kB isolated(anon):0kB isolated(file):48kB present:79248kB mlocked:0kB dirty:0kB writeback:0kB

mapped:504kB shmem:8784kB slab_reclaimable:420kB slab_unreclaimable:7488kB kernel_stack:520kB pagetables:384kB

unstable:0kB bounce:0kB writeback_tmp:0kB pages_scanned:13 all_unreclaimable? yes
lowmem_reserve[]: 0 0
Normal: 15*4kB 1*8kB 6*16kB 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 1*2048kB 0*4096kB = 2212kB
2210 total pagecache pages
19968 pages of RAM
658 free pages
1311 reserved pages
845 slab pages
150 pages shared
0 pages swap cached
[ pid ] uid tgid total_vm rss cpu oom_adj oom_score_adj name
[ 467] 0 467 218 20 0 -17 -1000 udevd
[ 882] 0 882 442 13 0 0 0 telnetd
[ 893] 0 893 46 3 0 0 0 XDVRStart.hisi
[ 894] 0 894 444 16 0 0 0 login
[ 895] 0 895 46 4 0 0 0 XDVRStart.hisi
[ 896] 0 896 443 14 0 0 0 sh
[ 897] 0 897 67218 11867 0 0 0 td3520d
[ 966] 0 966 444 15 0 0 0 udhcpc
Out of memory: Kill process 897 (td3520d) score 609 or sacrifice child
Killed process 897 (td3520d) total-vm:268872kB, anon-rss:46964kB, file-rss:504kB
HiDog: Unexpected close, not stopping watchdog!
HiDog: Watchdog is disabled!
MMB LEAK(pid=897): 0x8EBDA000, 28672 bytes, ''
mmz_userdev_release: mmb<0x8EBDA000> mapped to userspace 0x400a1000 will be force unmaped!
MMB LEAK(pid=897): 0x8EBE3000, 413696 bytes, ''
mmz_userdev_release: mmb<0x8EBE3000> mapped to userspace 0x40ed6000 will be force unmaped!
Killed
DVRService.cpp, 141 system exit!

[anmik]

Ссылка на скачанный дамп, прошивку с сайта и лог загрузки.
https://yadi.sk/d/yUikElb6wERlwA

[karadjia]

Читаем, стараемся понять и потом делаем как в https://www.cctvsp.ru/articles/vosstano ... os-parolya
Единственное что там не сказано, в статье этой, что для получения всех этих
u-boot.bin.img
u-boot.env.img
romfs-x.cramfs.img
user-x.cramfs.img
web-x.cramfs.img
custom-x.cramfs.img
нужно Вашу скачанную прошивку переименовать из хххххххххх.bin в ххххххххх.rar или ххххххххх.zip А вот тогда открыть этот архив и там эти файлы появятся

[anmik]

По этой ссылке уже читал. Файл разархивировал. Как залить эти файлы и какие нужно, я пока не понимаю. Вот что получилось:

[oleglevsha]

Читаем, стараемся понять и потом делаем как в https://www.cctvsp.ru/articles/vosstano ... os-parolya
Единственное что там не сказано, в статье этой, что для получения всех этих
u-boot.bin.img
u-boot.env.img
romfs-x.cramfs.img
user-x.cramfs.img
web-x.cramfs.img
custom-x.cramfs.img
нужно Вашу скачанную прошивку переименовать из хххххххххх.bin в ххххххххх.rar или ххххххххх.zip А вот тогда открыть этот архив и там эти файлы появятся

Мудрое решение

[dede]

Если честно, не слишком она поврежденной выглядит, ну может конфиги нужно поудалять...основное приложение падает из-за нехватки памяти, возможно это результат поврежденного конфига. Инструкция с сайта не поможет

[fobos]

вот бы еще фото платы с двух сторон в качестве...а то сильно похоже на TVT

[anmik]

Смущают последние строки загрузки лога:

Out of memory: Kill process 897 (td3520d) score 609 or sacrifice child
Killed process 897 (td3520d) total-vm:268872kB, anon-rss:46964kB, file-rss:504kB
HiDog: Unexpected close, not stopping watchdog!
HiDog: Watchdog is disabled!
MMB LEAK(pid=897): 0x8EBDA000, 28672 bytes, ''
mmz_userdev_release: mmb<0x8EBDA000> mapped to userspace 0x400a1000 will be force unmaped!
MMB LEAK(pid=897): 0x8EBE3000, 413696 bytes, ''
mmz_userdev_release: mmb<0x8EBE3000> mapped to userspace 0x40ed6000 will be force unmaped!
Killed
DVRService.cpp, 141 system exit!

То есть остаётся только вариант поиска и заливки рабочего дампа с такой же платы?
Фото платы завтра добавлю. От TVT TD-2704AS-SL-SUD заливал прошивку, регик не запустился. Да и не должен (наверно) т.к прошивки сравнивал, прошивки отличаются.

[fobos]

TVT TD-2704AS-SL-SUD - этого достаточно...заливали дамп или прошивку?

[anmik]

Дамп. Нашел в одной из тем с вашим участием. Дампы сравнивал, с первых адресов начинаются отличия.

Завтра попытаюсь конфиги позатирать.

[anmik]

Фото платы: