После неудачной прошивки не загружается регистратор. Подключился консольным кабелем, вот полный лог загрузки:
Код: Выделить всё
Bootrom start
Boot from NAND
Starting fastboot ...
System startup
DDRS
Reg Version: v1.1.0
Reg Time: 2015/11/10 14:22:31
Reg Name: hi3798mdmo1a_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_tvt_nand.reg
Relocate Boot to DDR
Jump to DDR
Compressed-boot v1.0.0
Uncompress.......Ok
System startup
Reg Version: v1.1.0
Reg Time: 2015/11/10 14:22:31
Reg Name: hi3798mdmo1a_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_tvt_nand.reg
Relocate Boot to DDR
Jump to DDR
Fastboot 3.3.0 (lizihao@ubuntu) (Mar 07 2019 - 18:16:06)
Fastboot: Version 3.3.0
Build Date: Mar 7 2019, 18:16:30
CPU: Hi3798Mv100
Boot Media: NAND
DDR Size: 1GB
Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x98 0xD1 0x90 0x15 0x76 0x14 0x01 0x00
Nand: Toshiba NAND 128MiB 3,3V 8-bit
Nand(HW-Auto): Block:128KB Page:2KB OOB:64B ECC:4bit/512 Chip:128MB*1
Boot Env on NAND
Env Offset: 0x00220000
Env Size: 0x00020000
Env Range: 0x00080000
boot_check_valid-->303, cmdBuf:mw.b 0x3F7FB000 0xFF 0x100000;nand read 0x3F7FB000 0x20000 0x100000
NAND read: device 0 offset 0x20000, size 0x100000
pure data length is 1048576, len_incl_bad is 1048576
request to read 0x100000, and read 0x100000 successfully!
1048576 bytes read: OK
do_start_boot-->338, boot from 0x20000
do_start_boot-->358, cmdBuf:go 0x3F7FB040
## Starting application at 0x3F7FB040 ...
System startup
Reg Version: v1.1.0
Reg Time: 2015/11/10 14:22:31
Reg Name: hi3798mdmo1a_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_tvt_nand.reg
Relocate Boot to DDR
Jump to DDR
Compressed-boot v1.0.0
Uncompress....................Ok
System startup
Reg Version: v1.1.0
Reg Time: 2015/11/10 14:22:31
Reg Name: hi3798mdmo1a_hi3798mv100_ddr3_1gbyte_16bitx2_4layers_tvt_nand.reg
Relocate Boot to DDR
Jump to DDR
Fastboot 3.3.0 (lizihao@ubuntu) (Mar 07 2019 - 18:16:49)
Fastboot: Version 3.3.0
Build Date: Mar 7 2019, 18:17:16
CPU: Hi3798Mv100
Boot Media: NAND
DDR Size: 1GB
Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x98 0xD1 0x90 0x15 0x76 0x14 0x01 0x00
Nand: Toshiba NAND 128MiB 3,3V 8-bit
Nand(HW-Auto): Block:128KB Page:2KB OOB:64B ECC:4bit/512 Chip:128MB*1
Boot Env on NAND
Env Offset: 0x00220000
Env Size: 0x00020000
Env Range: 0x00080000
HI_OTP_LockIdWord,313: ID_WORD have already been locked
SDK Version: HiSTBLinuxV100R003C00CP0003
keyled repeat init
>> Loading 'kernel' image.
flag:0x50465041, flash value:0xffffffff
check_update_file, 235, name:firmware3798p
USB0: Register 1212 NbrPorts 2
USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
USB1: Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
1 Storage Device(s) found
Interface: USB
Device 0: Vendor: JetFlash Rev: 1100 Prod: Transcend 16GB
Type: Removable Hard Disk
Capacity: 14745.0 MB = 14.3 GB (30197760 x 512)
Partition 1: Filesystem: FAT32 "NO NAME "
Reserve Memory
Start Addr: 0x3FFFE000
Bound Addr: 0x8CF9000
Free Addr: 0x3EB58000
Alloc Block: Addr Size
0x3FBFD000 4194304
0x3F8FC000 3145728
0x3F8F9000 8192
0x3F8C4000 212992
0x3F7C3000 1048576
0x3F7BF000 12288
0x3F4BE000 3145728
0x3F1BD000 3145728
0x3F09C000 1179648
0x3EC9B000 4194304
0x3EB9A000 1048576
0x3EB79000 131072
0x3EB58000 131072
Press Ctrl+C to stop autoboot
NAND read: device 0 offset 0x600000, size 0x700000
pure data length is 7340032, len_incl_bad is 7340032
request to read 0x700000, and read 0x700000 successfully!
7340032 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.10.0_s40
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4574008 Bytes = 4.4 MiB
Load Address: 02000000
Entry Point: 02000000
Verifying Checksum ... OK
ZYFAN bootm_load_os 366, comp:0
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.0_s40 (zyfan@zyfan-ubuntu) (gcc version 4.4.1 (Hisilicon_v200(gcc4.4-290+glibc-2.11+eabi+nptl)) ) #3 SMP Mon Nov 9 18:24:45 CST 2015
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: bigfish
Ignoring unrecognised tag 0x726d6d73
Ignoring unrecognised tag 0x726d6d74
Ignoring unrecognised tag 0x726d6d76
cma: CMA: reserved 500 MiB at 20000000
cma: CMA: reserved 4 MiB at 3fc00000
Memory policy: ECC disabled, Data cache writealloc
CPU: Hi3798Mv100
PERCPU: Embedded 8 pages/cpu @81152000 s11968 r8192 d12608 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
Kernel command line: mem=1G console=ttyAMA0,115200 root=/dev/romblock3 rootfstype=squashfs mtdparts=hinand:5M(boot),1M(baseparam),7M(kernel),18M(rootfs),64M(appfs),16M(qte),4M(config),12M(log),1M(logo) mmz=ddr,0,0,500M
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 509724k/509724k available, 538852k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80825d00 (8312 kB)
.init : 0x80826000 - 0x80881ec0 ( 368 kB)
.data : 0x80882000 - 0x808d5668 ( 334 kB)
.bss : 0x808d5668 - 0x8094b7f4 ( 473 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:192
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
Console: colour dummy device 80x30
Calibrating delay loop... 2383.87 BogoMIPS (lpj=1191936)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 20605 entries in 61 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80615278 - 0x806152d0
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (9572.35 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0xf8b00000 (irq = 81) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0xf8006000 (irq = 82) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0xf8b02000 (irq = 83) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource timer3
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
CPU PMU: probing PMU on CPU 0
hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 2003
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
Found Nand Flash Controller V610.
Nand ID: 0x98 0xD1 0x90 0x15 0x76 0x14 0x01 0x00
Nand: Toshiba NAND 128MiB 3,3V 8-bit
Nand(HW-Auto): Block:128KB Page:2KB OOB:64B ECC:4bit/512 Chip:128MB*1
9 cmdlinepart partitions found on MTD device hinand
Creating 9 MTD partitions on "hinand":
0x000000000000-0x000000500000 : "boot"
0x000000500000-0x000000600000 : "baseparam"
0x000000600000-0x000000d00000 : "kernel"
0x000000d00000-0x000001f00000 : "rootfs"
0x000001f00000-0x000005f00000 : "appfs"
0x000005f00000-0x000006f00000 : "qte"
0x000006f00000-0x000007300000 : "config"
0x000007300000-0x000007f00000 : "log"
0x000007f00000-0x000008000000 : "logo"
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver ftdi_sio
usbserial: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver pl2303
usbserial: USB Serial support registered for pl2303
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
usbcore: registered new interface driver btusb
hi_mci1: eMMC/MMC/SD Device NOT detected!
hi_mci0: eMMC/MMC/SD Device NOT detected!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
oprofile: using timer interrupt.
Netfilter messages via NETLINK v0.30.
nfnl_acct: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Bridge firewalling registered
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
8021q: 802.1Q VLAN Support v1.8
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
ALSA device list:
No soundcards found.
VFS: Mounted root (squashfs filesystem) readonly on device 240:3.
Freeing unused kernel memory: 364K (80826000 - 80881000)
_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________
Not find ldconfig
[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
[RCS]: /etc/init.d/S80network
UBI: attaching mtd4 to ubi0
root login: UBI: scanning is finished
UBI: attached mtd4 (name "appfs", size 64 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 4/1, WL threshold: 128, image sequence number: 250653281
UBI: available PEBs: 0, total reserved PEBs: 512, PEBs reserved for bad PEB handling: 20
UBI: background thread "ubi_bgt0d" started, PID 873
UBI device number 0, total 512 LEBs (65011712 bytes, 62.UBIFS: background thread "ubifs_bgt0_0" started, PID 876
0 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "ubifs"(null)
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 60567552 bytes (57 MiB, 477 LEBs), journal size 8634368 bytes (8 MiB, 68 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 00000000-0000-0008-0000-000000000001, small LPT model
UBI: attaching mtd5 to ubi1
UBI: scanning is finished
UBI: attached mtd5 (name "qte", size 16 MiB) to ubi1
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 11/3, WL threshold: 128, image sequence number: 213522928
UBI: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB handling: 20
UBI: background thread "ubi_bgt1d" started, PID 882
UBI device number 1, total 128 LEBs (16252928 bytes, 15.UBIFS: background thread "ubifs_bgt1_0" started, PID 885
5 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
UBIFS: mounted UBI device 1, volume 0, name "ubifs"(null)
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 2412544 bytes (2 MiB, 19 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 00000000-0000-0008-0000-000000000001, small LPT model
now start mount block
yaffs: dev is 32505862 name is "mtdblock6" rw
yaffs: passed flags ""
yaffs: dev is 32505863 name is "mtdblock7" rw
yaffs: passed flags ""
UBIFS: un-mount UBI device 1, volume 0
UBIFS: background thread "ubifs_bgt1_0" stops
OR_clientConfig.xml nothing to do
OR_configVersionInfo.xml nothing to do
OR_runParameter.xml nothing to do
OR_systemInfo.xml nothing to do
diff: can't stat '/mnt/mtd/default/OR_funcpane.xml': No such file or directory
cp: can't stat '/mnt/mtd/default/OR_funcpane.xml': No such file or directory
cp: can't create '/etc/resolv.conf': File exists
Load hi_media.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Sep 25 2015, 15:12:02])
Load hi_mmz.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Sep 25 2015, 15:12:02])
Load hi_common.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Sep 25 2015, 15:11:58])
[WDG_DRV_ModInit][560], default parameters, index:0, enable:1, margin:120
Load hi_wdg.ko success (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Sep 5 2016, 14:24:03])
Load hi_gpio.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:43:57])
HI_DRV_GPIOI2C_Init OK(g_I2cNum=0, SCL=gpio No.0, SDA=gpio No.0).
HI_DRV_GPIOI2C_Init OK(g_I2cNum=3, SCL=gpio No.49, SDA=gpio No.50).
Load hi_gpioi2c.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Aug 13 2015, 13:58:30])
Load hi_i2c.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:44:59])
Mali: Mali device driver loaded
Load hi_tde.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:44:48])
DieID is locked!
Load hi_otp.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:45:16])
Load hi_demux.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:45:04])
Load hi_adec.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:45:49])
Load hi_vfmw.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Apr 14 2016, 09:35:09])
Load hi_svdec.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:48:12])
[00:00:03:589 ERROR-HI_PQ]:DRV_PQ_GetFlashPqBin[2611]:PQ bin param may not burned
[00:00:03:596 ERROR-HI_PQ]:HI_DRV_PQ_Init[225]:Load PQBin failed!
Load hi_pq.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Apr 19 2016, 11:20:24])
Load hi_vpss.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Apr 15 2017, 02:45:01])
Load hi_vdec.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Apr 5 2017, 11:27:20])
Load hi_cipher.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:45:14])
Load hi_hdmi.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Aug 17 2016, 14:50:13])
Load hi_adsp.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:45:32])
Load hi_aiao.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 25 2015, 17:33:55])
Load hi_vou.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Mar 22 2017, 14:40:33])
Load hi_pvr.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:49:05])
Load hi_fb.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:44:43])
Load hi_ir.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:43:59])
Load hi_jpegdec.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:44:56])
Load hi_jpegenc.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:49:03])
Load hi_png.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:48:46])
Load hi_venc.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Apr 14 2016, 09:29:32])
Load hi_aenc.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:49:29])
Load hi_keyled.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:49:25])
Load hi_vi.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:49:40])
enter temperature_control_thread
Load hi_pmoc.ko success. (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Dec 11 2015, 16:48:56])
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 98, io mem 0xf9890000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hiusb-ehci hiusb-ehci.1: HIUSB EHCI
hiusb-ehci hiusb-ehci.1: new USB bus registered, assigned bus number 2
hiusb-ehci hiusb-ehci.1: irq 94, io mem 0xf9930000
hiusb-ehci hiusb-ehci.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 3
hiusb-ohci hiusb-ohci.0: irq 99, io mem 0xf9880000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hiusb-ohci hiusb-ohci.1: HIUSB OHCI
hiusb-ohci hiusb-ohci.1: new USB bus registered, assigned bus number 4
hiusb-ohci hiusb-ohci.1: irq 95, io mem 0xf9920000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
[00:00:04:517 ERROR-HI_HDMI]:SI_TimerHandler[509]:Read EDID Fail.Read 6 times
usb 1-2: new high-speed USB device number 2 using hiusb-ehci
usb-storage 1-2:1.0: USB Mass Storage device detected
scsi0 : usb-storage 1-2:1.0
---HDMI kernel event(no UserCallBack): HOTPLUG. ---
hiusb-xhci hiusb-xhci.0: xHCI Host Controller
hiusb-xhci hiusb-xhci.0: new USB bus registered, assigned bus number 5
hiusb-xhci hiusb-xhci.0: irq 101, io mem 0xf98a0000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
hiusb-xhci hiusb-xhci.0: xHCI Host Controller
hiusb-xhci hiusb-xhci.0: new USB bus registered, assigned bus number 6
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3014.6.29 [Flags: R/W MODULE].
keybaord 3798m gpio init version : Aug 13 2015 14:19:00
[RTC]g_chip_type = 0
[PT4307]HI_DRV_GPIOI2C_CreateGpioI2c OK(g_I2cNum=3, SCL=gpio No.49, SDA=gpio No.50).
[RTC]pt4307 init Success!
version - chips : 201512280940+->xxxchips
TVT hi3798m CryptoMemory Device Driver v1.0.0: Dec 28 2015 18:22:50
[RT5616]HI_DRV_GPIOI2C_CreateGpioI2c OK(g_I2cNum=3, SCL=gpio No.49, SDA=gpio No.50).
[RT5616]Find Rt5616! Initial now!... ...
usb 6-1: new SuperSpeed USB device number 2 using hiusb-xhci
usb 6-1: Parent hub missing LPM exit latency info. Power management will be impacted.
usb-storage 6-1:1.0: USB Mass Storage device detected
scsi1 : usb-storage 6-1:1.0
[RT5616]Rt5616 Version:2015-8-13
libphy: himii: probed
scsi 0:0:0:0: Direct-Access JetFlash Transcend 16GB 1100 PQ: 0 ANSI: 6
sd 0:0:0:0: [sda] 30197760 512-byte logical blocks: (15.4 GB/14.3 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
udisk1210 -> /dev/sda
udisk1210p1 -> /dev/sda1
Up port phy at 0x01 is connect
libphy: PHY himii:1f not found
hieth_init ok version is 201512161630 rx cnt:1
netpnp init ok version : 201603021130
Setup mv88e6071 SWITCH...
smi_i2c_init ok
smi_i2c_phy_init ok
---the id 1 value:2000
smiRead failed i:1
the mv88e6071 chip cnt is 1
Setup mv88e6071 SWITCH OK
Register mv88e6071_phy_ops successfully 201708101600.
scsi 1:0:0:0: Direct-Access ASMT 2115 0 PQ: 0 ANSI: 6
sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: unknown partition table
sd 1:0:0:0: [sdb] Attached SCSI disk
udisk6110 -> /dev/sdb
[AppPackInfo]
softwareVersion=1.2.9.0
launchDate=20180530.0905
productInfo=3798M_POE
pkgId=
srcPkgDate=20180530.0905
branchVersion=0
productName=N0K
UILayout=UI1-X
UIStyle=UI1-A
pkgType=1290_prerelease
pkgFlag=4A414
pkgBatch=V
pkgOrder=0
pkgTimes=0
realSrcDate=20180602.1237
extInfo=058,Revision17279
This is PrepareUpgradeTo13X
modprobe: chdir(/lib/modules): No such file or directory
cat: can't open '/etc/init.d/mac.dat': No such file or directory
current flash param ==
------get 1------current param type == 130080, lenth:32, ver_type:1
data = 00:18:AE:7D:F4:99, type = 4065
IPv6: ADDRCONF(NETDEV_UP): phyeth0: link is not ready
mount: mounting none on /proc/bus/usb failed: No such file or directory
/mnt/mtd/dep2.sh: line 29: can't create /proc/irq//smp_affinity: nonexistent directory
argc = 2
[RTC_RD_TIME]
Current time value:
2021-3-2 5:9:36
Wait_HDIntoOS done.
Wait_DumpDiskIntoOS done.
appDaemon is ready..., pid=1321
update open close fb ++++++++++++++
1111 current set fb width 1280, height 1024, pstFrameBufParam->buf_number=2
xres_virtual = 1280, yres_virtual = 2048, xres = 1280, yres = 1024, pixel_fmt_size = 16, xoffset = 0, yoffset = 0
fb width 1280, height 1024, len 5242880, 2560
[1322@A#R@02-08:09:36]VAC_FBInitForUpdate ret=0[main.cpp:48]
[1322@A#R@02-08:09:36]nRet=18,_Dsize=38, [FrameBufferCtrl.cpp:884]
[1322@A#R@02-08:09:36]config part is /dev/mtdblock6, fs=yaffs2[Upgrade_1_0_X.cpp:112]
[1322@A#R@02-08:09:36]get UI=1A, sPfType=N0K[Upgrade_1_0_X.cpp:181]
[1322@A#R@02-08:09:36]=========== find /mnt/nfs/factoryConfig/OR_factoryConfig.xml ==============[Upgrade_1_0_X.cpp:329]
[1322@A#R@02-08:09:36]get customerID=25[Upgrade_1_0_X.cpp:337]
[1322@A#R@02-08:09:36]get byCustomModel=LTV-RNE-040-0G[Upgrade_1_0_X.cpp:342]
[1322@A#R@02-08:09:36]get byModel=TD-3204H1-4P, TVTproduct=TD_3204H1_4P[Upgrade_1_0_X.cpp:369]
[1322@A#R@02-08:09:36]get byPanelType=Q23[Upgrade_1_0_X.cpp:382]
[1322@A#R@02-08:09:36]get bySN=NF49902B44CP[Upgrade_1_0_X.cpp:387]
[1322@A#R@02-08:09:36]=========== find /mnt/nfs/factoryConfig/OR_volatileFactoryConfig.xml ==============[Upgrade_1_0_X.cpp:428]
<?xml version="1.0" encoding="UTF-8"?>
<factoryConfig>
<factoryParam>
<videoFormat>PAL</videoFormat>
<timeZone>MSK-3</timeZone>
<resolution type="resolution">
<item scale="false" index="0">1920x1080</item>
</resolution>
<languageCode>0x0419</languageCode>
<customerID id="025">RU32</customerID>
<deviceName>Device Name</deviceName>
</factoryParam>
</factoryConfig>
[1322@A#R@02-08:09:36]get videoFormat=PAL, byVideoFormat=1[Upgrade_1_0_X.cpp:438]
[1322@A#R@02-08:09:36]get byTimezone=MSK-3[Upgrade_1_0_X.cpp:443]
[1322@A#R@02-08:09:36]get byFactoryLanguage=0x0419[Upgrade_1_0_X.cpp:448]
[1322@A#R@02-08:09:36]get dwCustomID=25[Upgrade_1_0_X.cpp:454]
[1322@A#R@02-08:09:36]FillProductInfo tip:The customerID(25) not support in 1.3!, ret=0[main.cpp:64]
[1322@A#R@02-08:09:36]nRet=38,_Dsize=78, [FrameBufferCtrl.cpp:884]
libphy: himii:01 - Link is Down
libphy: himii:01 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): phyeth0: link becomes ready
Дальше загрузка не идёт, через пару минут сам перезагружается и всё по новой.
Вывод printenv:
Код: Выделить всё
fastboot# printenv
bootdelay=1
baudrate=115200
ipaddr=192.168.1.10
serverip=192.168.1.1
netmask=255.255.255.0
bootfile="uImage"
bootargs_2G=mem=2G mmz=ddr,0,0,600M
update_force=1
gatewayip=192.168.4.1
ethaddr=A6:89:0D:90:65:29
update_force_boot=0
update_force_others=0
bootargs_1G=mem=1G mmz=ddr,0,0,500M
updated_appfs_special_flag=1
stdin=serial
stdout=serial
stderr=serial
bootargs=mem=1G console=ttyAMA0,115200 root=/dev/romblock3 rootfstype=squashfs mtdparts=hinand:5M(boot),1M(baseparam),7M(kernel),18M(rootfs),64M(appfs),16M(qte),4M(config),12M(log),1M(logo)
bootcmd=nand read 0x1000000 0x600000 0x700000;bootm 0x1000000
bootargs_512M=mem=512M mmz=ddr,0,0,328M
ver=Fastboot 3.3.0 (lizihao@ubuntu) (Mar 07 2019 - 18:16:49)
Environment size: 709/131068 bytesКод: Выделить всё
fastboot# help
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
clear_bootf- clear Hibernate!! bootflag
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
ddr - ddr training function
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
getinfo - print hardware information
go - start application at address 'addr'
help - print command description/usage
hibernate- Hibernate!! boot
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mtest - simple RAM read/write test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nm - memory modify (constant address)
otp_burntoecurechipset- Burn to secure chipset, please be careful !!!
otp_getcustomerkey- otp_getcustomerkey
otp_getstbprivdata- otp_getstbprivdata
otp_setstbprivdata- StbPrivData
otpreadall- read otp ,for example otpreadall
otpwrite- write otp ,for example otpwrite adddress value
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv - set environment variables
tftp - tftp - download or upload image via network using TFTP protocol
unzip - unzip a memory region
uploadx - upload binary file over serial line (xmodem mode)
usb - USB sub-system
usbboot - boot from USB device
usbburn - burn file from USB device
version - print monitor versionКод: Выделить всё
setenv auversion0
setenv auversion1
setenv auversion2
setenv auversion3
setenv auversion4
setenv auversion5
setenv auversion6
saveenv
resetКод: Выделить всё
ubt3798
rfs3798
krn3798
fastboot.bin
baseparam3798
appfs3798
