Сегодня ремонтировал longse LS-CVR5216,проблемы с "железом",ремонт удался.Решил слить прошивку для коллекции.И тут вылезла проблема-подключившись к UART ,вместо привычного U-Boot увидел такое:
Uncompressing Linux... done, booting the kernel.
start to copy FC7500 core boot image...
done, FA6 core now is booting.
ARM eCos 13:48:21
Dec 18 2014
[GM8210] eCos version: 2014_1218_1116, minor version: 1218_1116
<ECOS> Dump Heap 1 Memory information (malloc):
<ECOS> total size of entire pool = 7167512
<ECOS> number of chunks free for use = 1
<ECOS> total allocated space in bytes = 528
<ECOS> total space in bytes not in use = 7166964
<ECOS> size of largest unused block = 7166964
<ECOS> log buffer address: 0x12a400, size: 524288
ECOS: Wait Host core to provide the mbox .Booting Linux on physical CPU 0
Linux version 3.3.0 SVN:5530 (jenkins@localhost.localdomain) (gcc version 4.4.0 20100318 (experimental) (Buildroot 2012.02) ) #1 PREEMPT Mon Sep 7 10:37:05 CST 2015
CPU: FA6 [66056262] revision 2 (ARMv5TE), cr=0000397f
CPU VIPT aliasing data cache, unknown instruction cache
Machine: Grain-Media GM8210
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 164592
Kernel command line: initrd=0x37800000,0x300000 ramdisk_size=10240 root=/dev/ram rw init=/init mem=256M@0x10000000 gmmem=190M console=ttyS0,115200 mem=392M@0x20000000
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 648MB = 648MB total
Memory: 648800k/648800k available, 14752k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xa9000000 - 0xff000000 (1376 MB)
lowmem : 0x80000000 - 0xa8800000 ( 648 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x804f4894 (5043 kB)
.init : 0x804f5000 - 0x80518000 ( 140 kB)
.data : 0x80518000 - 0x8053d0a0 ( 149 kB)
.bss : 0x8053d0c4 - 0x80585978 ( 291 kB)
NR_IRQS:128
Timer use APB0 clock
gm_jiffies_init, system HZ: 100, pClk: 46500000
console [ttyS0] enabled
Calibrating delay loop... 738.09 BogoMIPS (lpj=3690496)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x103ac698 - 0x103ac704
devtmpfs: initialized
FMEM: 48640 pages(0xbe00000 bytes) from bank0 are reserved for Frammap.
FMEM: 96256 pages(0x17800000 bytes) from bank1 are reserved for Frammap.
FMEM: Logical memory ends up at 0xa8800000, init_mm:0x80004000(0x10004000), PAGE_OFFSET:0x80000000(phys:0x10000000),
Fmem hooks external data-abort handler.
NET: Registered protocol family 16
PMU: Mapped at 0xfe000000
IC: GM8210, version: 0x11
PCIE PMU: Mapped at 0xfe00a000
IC: GM8312(1)
iotable: VA: 0xfe000000, PA: 0x99000000, Length: 4096
iotable: VA: 0xfe001000, PA: 0x98300000, Length: 4096
iotable: VA: 0xfe002000, PA: 0x98400000, Length: 4096
iotable: VA: 0xfe003000, PA: 0x98500000, Length: 4096
iotable: VA: 0xfe004000, PA: 0x98800000, Length: 4096
iotable: VA: 0xfe005000, PA: 0x98900000, Length: 4096
iotable: VA: 0xfe006000, PA: 0x82600000, Length: 4096
iotable: VA: 0xfe007000, PA: 0x99100000, Length: 4096
iotable: VA: 0xfe008000, PA: 0x98d00000, Length: 4096
iotable: VA: 0xfe009000, PA: 0x96000000, Length: 4096
iotable: VA: 0xfe00a000, PA: 0xc2700000, Length: 4096
iotable: VA: 0xfe00b000, PA: 0xc2800000, Length: 4096
8210 PCIE: 0xa9008000(0x99e00000), 8312 PCIE: 0xa900a000(0xc3700000)
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.24.
Switching to clocksource fttmr010:1
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 3072K
Video Timer(timer3) Max 92000ms in 0xfefd1980 HZ.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. (NAND) A© 2001-2006 Red Hat, Inc.
msgmni has been set to 1273
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
gpiochip_add: registered GPIOs 0 to 31 on device: ftgpio010.0
probe ftgpio010.0 OK, at 0xa987c000
gpiochip_add: registered GPIOs 32 to 63 on device: ftgpio010.1
probe ftgpio010.1 OK, at 0xa987e000
Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xfe002000 (irq = 10) is a 16550A
brd: module loaded
loop: module loaded
FTSATA100_AHCI driver version 0.15
bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
nice use GMAC0
ftgmac100: Loading version 0.1 ...
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_ncm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
ftiic010 ftiic010.0: irq 18, mapped at a9882000
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 10
Mobile IPv6
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RAMDISK: lzma image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
devtmpfs: mounted
Freeing init memory: 140K
mount: mounting none on /dev/pts failed: No such file or directory
mdev: applet not found
mount: mounting none on /dev/pts failed: No such file or directory
mount: mounting tmpfs on /dev/shm failed: No such file or directory
[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
mkdir: can't create directory '/dev/pts': File exists
/etc/init.d/S01udev: line 7: /sbin/mdev: not found
[RCS]: /etc/init.d/S81toe
[RCS]: /etc/init.d/S99dahua
S99dahua&...
Mounting root fs rw ...
/ # Mounting other filesystems ...
Setting hostname ...
/etc/init.d/S99dahua: line 11: hostname: not found
############## frammap.ko svn 25569 Sep 6 2015 18:26:38
Frammap: DDR0: memory base=0x14000000, memory size=0xbe00000, align_size = 4K.
Frammap: DDR1: memory base=0x20000000, memory size=0x17800000, align_size = 4K.
Frammap: version 1.1.2, and the system has 2 DDR.
Frammap: fail to open /mnt/mtd/config_8210, /tmp/template_8210 is created.
/etc/init.d/S99dahua: line 14: mdev: not found
rm: can't remove '/mnt/mtd/avss.info': No such file or directory
rm: can't remove '/mnt/mtd/Config/input_res': No such file or directory
*HOST FA626*
cpucomm svn 25569 Sep 6 2015 18:26:32
ep_cnt = 0, non_ep_cnt = 2
mem_alloc_init: physical memory begins at 0x14000000, ends at 0x15000000, 0x1000000 bytes.
cpucomm: use dmach mask: 0xc0
Wait Host core to provide the mbox .done
--- mbox paddr: 0xc800000, vaddr: 0xaa0ae000 ---
Wait FA726 core ready...done
--- ECOS: mbox paddr: 0xc800000, vaddr: 0xc800000 ---
ECOS: Wait FA626 core ready..done
cpucomm: board FA726, PoolMem:(paddr:0xc800000, size:0x2800000, vaddr:0xad000000, cbaddr:0xb0000000). ShareMem:(paddr:0xc801000, size:0x12000, vaddr:0xad001000)
--- mbox paddr: 0xc800000, vaddr: 0xaa0ae000 ---
Wait FC7500 core ready..done
cpucomm: board FC7500, PoolMem:(paddr:0x0, size:0x1000000, vaddr:0xb3000000, cbaddr:0xb5000000). ShareMem:(paddr:0xfde6f0, size:0x12000, vaddr:0xb3fde6f0)
ok, cpu_comm_2.7 driver is executed in FA626 core with dma_type: 1(1).
Begin recv file from FA726...
ECOS FC7500 for FA626 core, share memory phyaddr: 0x14016000, size: 0x12000, vaddr: 0x14016000
ECOS FC7500 for FA626 core, pool memory phyaddr: 0x14000000, size: 0x1000000, vaddr: 0x14000000
CPU_COMM version: 2.2 in FC7500
ecos_device_open -- FC7500 Record opens a channel for read/write.
ecos_device_open -- FC7500 Playback opens a channel for read/write.
ecos_device_open -- FC7500 Heart beat opens a channel for read/write.
End recv file from FA726...
video_system PAL
/mnt/mtd/avss.info
get_tv_support:0
get_dh9901_dev_num:2
----------------------------------------------------------------
ddr name: frammap0
base: 0x14000000
end: 0x1fe00000
size: 0xbe00000 bytes
memory allocated: 0x1000000 bytes
memory free: 0xae00000 bytes
max available slice: 0xae00000 bytes
memory allocate count: 1
clear address: 0x15000000
dirty pages: 4096
clear pages: 44544
size alignment: 0x1000
-------------------------------------------log: module license 'GM' taints kernel.
----------------Disabling lock debugging due to kernel taint
-----
ddr name: frammap1
base: 0x20000000
e
log.ko:svn 25569 Sep 6 2015 18:26:25 (mmap 0x82810000 size 0xc000)
nd: 0x37800000
size: 0x1780000
LOG base 0xaa0c3000 size 512K (start pointer 0x7f029314)
0 bytes
memory PAGE_OFFSET(0x80000000) VMALLOC START(0xa9000000) HZ(100)
allocated: 0x0 bytes
memory fropen /mnt/mtd/Config/vcapMode.cfg error
ee: 0x17800000 bcpu_type=18 video_chip=19 digital_chn_num=0 video_chn_num=16 speceial_custom 0,audio_chn_num=4 abroad=0 hwid=0x40000dd iva_support=0 mic_mux=1 tv_support=0 vstd=0 ad_dev_num=4 input_res 0 vcap_mode=-1
ytes
max available slice: 0x17800000 bytes
memory allocate count: 0
clear address: 0x20000000
dirty pages: 0
clear pages: 96256
size alignment: 0x1000
ms.ko v0.8 svn 25569 Sep 6 2015 18:26:28
em.ko v0.26 svn 25569 Sep 6 2015 18:26:08
em_user v0.6 Sep 6 2015 18:26:08
Start EM thread 0(em_callback:0) with nice -20
Start EM thread 1(em_callback:1) with nice -20
EM Module Service Starting (callback_period = 3ms)
Start EM thread 2(em_callback:2) with nice -20
input_res = 7
output_type = 50
LCD platform: Hook GM8210 driver.
[mod0]fb0_num[1],fb1_num[1],fb2_num[1],output_type[50],input_res[7],lcd_disable[0],fb0_fb1_share[0],fb1_pan_display[0],vs_width[0],vs_height[0],bf[0],d1_3frame[0],gui_clone_fps[25]
GM_ffb: [ver:0.1.19]INIT flcd200 OK.
LCD0: PA = 0x9a800000, VA = 0xaa1e0000, size:0xd000 bytes
LCD0(SLI10121): Output resolution is 1280x1024/60HZ.
LCD0: Input resolution is 1280x1024(SXGA)
LCD0 registers 1 entities to video graph!
LCD0: Driver[Ver: 1.2.2] init ok. fb0_fb1_share:0, fb1_pan_display:0
zebra_device_open -- lcd0_drv opens a channel for read/write.
[mod1]fb0_num[1],fb1_num[1],fb2_num[1],output_type[1],input_res[1],lcd_disable[1],fb0_fb1_share[0],fb1_pan_display[0],vs_width[0],vs_height[0],bf[0],d1_3frame[1],gui_clone_fps[10]
GM_ffb: [ver:0.1.19]INIT flcd200_2 OK.
LCD2: PA = 0x9b800000, VA = 0xaa1f0000, size:0xd000 bytes
LCD2: Output resolution is D1 PAL.
Register codec TVE100.
LCD2: Input resolution is PAL
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
The standard clock is 27.0MHZ, but gets 558MHZ. Please correct PLL!
LCD2 joins D1 of 3frame.
LCD2: Driver[Ver: 1.2.2] init ok. fb0_fb1_share:0, fb1_pan_display:0
zebra_device_open -- lcd2_drv opens a channel for read/write.
HDMI sli10121 works in PCIe mode, pa = 0xc1900000, va = 0xaa1d8000.
Register codec sli10121-480P_BT1120.
Register codec sli10121-576P_BT1120.
Register codec sli10121-1024x768_RGB.
sli-hdmi is in 1280x1024 RGBLCD210: Input format to sli-hdmi is RGB888.
sli10121_polling_thread INIT = 0
HDMI_init, 1
Register codec sli10121-1280x1024_RGB.
Register codec sli10121-1920x1080_RGB.
Register codec sli10121-1280x720_RGB.
sli10121 sleep 100 ms
fe_common version 140714
zebra_device_open -- hdmi opens a channel for read/write.
i2c_test=0,dev_num=2,clk_used=0 clk_src=4 clk_freq=27000000 init=1 rstb_used=0 ch_map=0 sample_rate=0 sample_size=1 notify=1 audio_num=4 codec_type=2 hwid=67109085 isDev626=0 video_chip=19 encode_type=0 mic_mux=1 iaddr=60 =62 vout_format=0 =0 vout_mode=0 =0
******************************************************************************
adda.ko: Version: V0.00.074 Svn: 25569 Compile at Sep 6 2015 18:28:51
******************************************************************************
video_chip=19
audio_num=4
mic_mux=1
codec_type=2
res:7 brightness_value:-5 onoff:0
hdmi_test mode=0
SLI HDMI_interrupt, MASK_92h = 0xc0, INT_94h = 0x0
SANK_BAD_PCB
SANK_BAD_PCB
adda_sys_channel_maps: hwid=0x40000dd
adda_sys_channel_maps: hwid=0x40000dd
dh9910_config_vdport: stDH9910VdPortConfig[0].ucVClkConfig = 0xaa
dh9910_config_vdport: stDH9910VdPortConfig[1].ucVClkConfig = 0xaa
dh9910_config_vdport: stDH9910VdPortConfig[2].ucVClkConfig = 0xaa
dh9910_config_vdport: stDH9910VdPortConfig[3].ucVClkConfig = 0xaa
adda_sys_channel_maps: hwid=0x40000dd
dh9910_video_init begin VD_PORT_MUX_MOD 0
dh9910_video_init ChipId 0 end
audio audio 9910!
dh9910_audio_init: first Stage of cascade
DH9910#0 Init...OK!
adda_sys_channel_maps: hwid=0x40000dd
dh9910_video_init begin VD_PORT_MUX_MOD 0
dh9910_video_init ChipId 1 end
audio audio 9910!
dh9910_audio_init: second Stage of cascade
DH9910#1 Init...OK!
cap_scl_up_disable =0
[VCAP_INFO]: VCAP300 Version: 0.3.5A svn 25569 Sep 6 2015 18:26:55
HOST626! insert vcap!\n
vi_mode [1 1 1 1], cap_md=1,grab_filter=0
vport= 0x4321,0x8765,inv_clk =0 0 data_swap 0 0
adda_sys_channel_maps: hwid=0x40000dd
dhcvi_vport_map: vport[0]=0x5678
dhcvi_vport_map: vport[1]=0x1324
dhcvi_vport_map: vport[2]=0x0
dhcvi_vport_map: vport[3]=0x0
adda_sys_channel_maps: hwid=0x40000dd
[VCAP_INFO]: Register DH9910#0 Input Device
[VCAP_INFO]: Register DH9910#1 Input Device
[VCAP_INFO]: Register Generic Input Device 8
max_vch_num=128,max_minors=100,temp_width=1920,temp_height=1080,scal_dmaparm=0
scaler300.ko:version 141017, svn 25569 Sep 6 2015 18:27:05
fscaler300_init_one [0] NCNB
fscaler300_init_one [1] NCNB
scaler_trans_init, version: 0x20140822
scaler_trans_init, Wait RC FA726 provides the directIO memory...
.a0?>?
Что это?И как в этом случае работать?
Пришлось сохранять дамп на программаторе.Пристёгиваю фото аппарата.
longse LS-CVR5216
longse LS-CVR5216
- Вложения
-
-
-
