

U-Boot 2010.06 (Sep 02 2016 - 09:37:59)

Flash: 1.1 MiB
Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0xc2 0x20 0x18
Block:64KB Chip:16MB Name:"MX25L128XX"
SPI Nor total size: 16MB
SPI Nand ID Table Version 1.4
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  1  0 
OpenDev  vo:0 intf_type:36 out_sync:17
dev 0 opened!
logo lay = 0, x =0,y = 0, w =1024,h = 768
logo x = 0, y =0,w = 1024, h =768
graphic layer 0 opened!
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
USB founded

** Invalid boot device **
kernel.img founded

** Invalid boot device **
all.img founded
16384 KiB hi_fmc at 0:0 is now current device
flash_reinit enddev id: type = 1, num = 0, size = 0x00f80000, mtd_id = single part
part  : name = static, size = 0x00f80000, offset = 0x00000000
mtdpart init end
--- jffs2_part_info: partition number 0 for device nor0 (single part)
### JFFS2 loading 'mode_type' to 0x82000000
Scanning JFFS2 FS:   .   done.

### JFFS2 load complete: 3 bytes loaded to 0x82000000
16384 KiB hi_fmc at 0:0 is now current device
flash_reinit endmtdpart init end
--- jffs2_part_info: partition number 0 for device nor0 (single part)
### JFFS2 loading 'logo.jpg' to 0x9f000000
### JFFS2 load complete: 138986 bytes loaded to 0x9f000000
jpeg decoding ...
<<addr=0x9f000000, size=0x60000, vobuf=0x9f000000>>
mmu_enable
<<imgwidth=800, imgheight=600, linebytes=1600>>
decode success!!!!
decode jpeg!
dev 0 set background color = 0x0-> 0x0!
OpenDev  vo:0 intf_type:36 out_sync:17
dev 0 opened!
dev 1 set background color = 0x0-> 0x0!
OpenDev  vo:1 intf_type:1 out_sync:1
dev 1 opened!
logo lay = 0, x =0,y = 0, w =1024,h = 768
logo x = 112, y =84,w = 800, h =600
graphic layer 0 opened!
logo lay = 1, x =0,y = 48, w =720,h = 480
logo x = 2147483608, y =2147483588,w = 800, h =600
graphic layer 1 opened!
flash_reinit endmtdpart init end
--- jffs2_part_info: partition number 0 for device nor0 (single part)
### JFFS2 loading 'uImage' to 0x82000000
### JFFS2 load complete: 4651800 bytes loaded to 0x82000000
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.10.0
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4651736 Bytes = 4.4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux...

LZMA data is corrupt

 -- System halted