
Checking DDR......OK

UBL Version: 1.46t(DM365)21:46:29 Aug  3 2017
 Oscillator: 24MHZ
 ARM Rate: 432 MHZ
 DDR Rate: 340 MHZ
 BootMode: SPI 
Starting SPI Memory Copy...
DONE


U-Boot 1.3.6 (jerry) (Aug  3 2017 - 21:50:01)

DRAM:  128 MB
SF: Got idcode c2 20 18 c2 20
In:    serial
Out:   serial
Err:   serial
Ethernet PHY: GENERIC @ 0x01,id:1cc816
total gio 2
gio[22]=1
gio[25]=1
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending through gateway 192.168.1.1
Filename 'upgrade_info_7db780a713a4.txt'.
Load address: 0x80100000
Loading: *
Retry count exceeded; starting again
Fail to get info file!
Init error!
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending through gateway 192.168.1.1
Filename 'failed.txt'.
Load address: 0x80200000
Loading: *
Retry count exceeded; starting again
==>use default images
APP_OFFSET_NEW test
........
## Booting kernel from Legacy Image at 80007fc0 ...
   Image Name:   Linux-2.6.18_pro500-davinci_evm-
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1912092 Bytes =  1.8 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   XIP Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................ done, booting the kernel.
Linux version 2.6.18_pro500-davinci_evm-arm_v5t_le (jenkins@centos234) (gcc version 4.2.0 (MontaVista 4.2.0-16.0.32.0801914 2008-08-30)) #1 PREEMPT Thu Aug 3 21:47:53 CST 2017
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: DaVinci DM365 EVM
new hwid:VTO2111D:0:4:1:1d:5:0:1:9:3:3:0:1B0:0:2:0:0:0:0:0
Memory policy: ECC disabled, Data cache writeback
DaVinci DM0365 variant 0x8
prediv = 6, pll0_mult = 85, postiv = 1, pll_div4 = 4, pll_rate = 680000000, pll_div6 = 25
PLL0: fixedrate: 24000000, commonrate: 170000000, vpssrate: 340000000 PLL1_ARMRATE = 340000000
PLL0: vencrate_sd: 27200000, ddrrate: 340000000 mmcsdrate: 136000000
##: prediv = 1, pll1_mult = 9,  postdisv = 1, pll-rate = 432000000, pll_div2 = 1, pll_div4 = 21, pll-div5 = 16
PLL1: armrate: 432000000, voicerate: 20571428, vencrate_hd: 27000000, ddrratePLL2 = 432000000
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Built 1 zonelists.  Total pages: 24320
dh_keyboard:0
PID hash table entries: 512 (order: 9, 2048 bytes)
Clock event device timer0_0 configured with caps set: 07
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 95MB = 95MB total
Memory: 92160KB available (3193K code, 775K data, 188K init)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
MUX: initialized SPI0_SDENA0
DaVinci: 104 gpio irqs
MUX: initialized GPIO20
MUX: initialized I2C_SCL
pMem_relimitBaseAddr:0xc6000000
Generic PHY: Registered new driver
configured buff delay: 50

SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
MUX: initialized SPI2_SDENA0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
LTT : ltt-facilities init
LTT : ltt-facility-core init in kernel
davinci_wdt_init proc enable
rtc probe addr 0x68, probeByte 0x00...
rtc probe addr 0x6f, probeByte 0x00...
rtc probe addr 0x57, probeByte 0x00...
rtc probe addr 0x32, probeByte 0x00...
probe none!!! change to another probeByte
rtc probe addr 0x68, probeByte 0x10...
rtc probe addr 0x6f, probeByte 0x10...
rtc probe addr 0x57, probeByte 0x10...
rtc probe addr 0x32, probeByte 0x10...
RTC_i2c_attach_client:addr:0x32
regValue:0x28
 == Found RTC chip RX8010, I2C addr 0x32 == 
probe really none!!!DS1338  driver v1.04sem  proc enable, 
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
&&&: uart_add_one_port, line = 0, uartclk = 0
&&&: uart_add_one_port, line = 1, uartclk = 170000000
ttyS0: autoconf (0x0000, 0xfbc20000): <6>serial8250.0: ttyS0 at MMIO map 0x1c20000 mem 0xfbc20000 (irq = 40) is a 16550A
&&&: uart_add_one_port, line = 0, uartclk = 24000000
ttyS1: autoconf (0x0000, 0xfbd06000): <6>serial8250.0: ttyS1 at MMIO map 0x1d06000 mem 0xfbd06000 (irq = 41) is a 16550A
&&&: uart_add_one_port, line = 1, uartclk = 170000000
Broadcom BCM5411: Registered new driver
Broadcom BCM5421: Registered new driver
Broadcom BCM5461: Registered new driver
Broadcom BCM5481: Registered new driver
Broadcom BCM54811: Registered new driver
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Linux video capture interface: v2.00
i2c /dev entries driver
System bootup mode:SPI
JECDEC ID : 0xc22018
ext_jedec ID : 0xc220
chip id mx25l12805d
found mx25l12805d in table.
m25p80 spi0.0: mx25l12805d (16384 Kbytes)
Creating 10 MTD partitions on "spi0.0":
0x00000000-0x00040000 : "bootloader"
0x00040000-0x00060000 : "HWID"
0x00060000-0x00260000 : "kernel"
0x00260000-0x003e0000 : "web"
0x003e0000-0x006e0000 : "rootfs"
0x006e0000-0x006f0000 : "product"
0x006f0000-0x00da0000 : "user"
0x00da0000-0x00ec0000 : "data"
0x00ec0000-0x00f60000 : "backup"
0x00f60000-0x01000000 : "config"
dm_spi.0: davinci SPI Controller driver at 0xc6266000 (irq = 42) use_dma=0
[*****geyj******1]register master =0xc0558800;bus_num = 0 
dm_spi.2: davinci SPI Controller driver at 0xc6268800 (irq = 21) use_dma=0
[*****geyj******1]register master =0xc0558400;bus_num = 2 
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
usbcore: registered new driver zaurus
musb_hdrc: version 6.0, pio, host, debug=0
Pin GPIO33 already used for SPI2_SDENA0.
musb_hdrc: USB Host mode controller at c626a000 using PIO, IRQ 12
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
u32 classifier
    Performance counters on
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (760 buckets, 6080 max) - 224 bytes per conntrack
ctnetlink v0.90: registering with nfnetlink.
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Time: timer0_1 clocksource has been installed.
Clock event device timer0_0 configured with caps set: 08
Switched to high resolution mode on CPU 0
IP-Config: No network devices available.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 188K
init started: BusyBox v1.9.1 (2017-06-12 16:54:28 CST)
starting pid 216, tty '': '/etc/init.d/dnode'
3.86s
starting pid 221, tty '': '/etc/init.d/rcS'
cp: cannot stat '/sbin/telnetd': No such file or directory
Sun Jan 13 22:23:20 2019  0.000000 seconds
mount: mounting /dev/mtdblock5 on /mnt/pd failed: Invalid argument
[gpio] SD card hardware reset is done, gio55=0.
[gpio] adc init!
[gpio] initialize success, build at 21:50:06, Aug  3 2017[gpio] CMD=9, Setting product type: 0
[libdv[gpio] CMD=4, Setting product fchip: 29
r] 
libdvr.so B[gpio] CMD=3, Setting hardware version: 0
uild time: Aug  3 2017 at 21:48:46.
[libdvr] SVN NUM: 7773.
GIO_SET_PRODUCT_TYPE = 9
[gpio] SD card hardware reset is done, gio55=0.
current wdt period=5000 ms
[libdvcurrent wdt period=25000 ms
r] 
libdvr.so Build time: Aug  3 2017 at 21:48:46.
[libdvr] SVN NUM: 7773.
[syshelper] V1.21(no exit): startup time=25 s, appauto=0, hctosystime=1500,type=0
[syshelper] start watch dog success, period is 25000 ms.
coremnt not found
5.78s

7z ANSI-C Decoder 9.20 : Igor Pavlov : Public domain : 2010-11-18

DH:: [rootlistinit:909] rootlistinit  buf len=53  

Extracting 8188eu.ko
Extracting cmemk.ko
Extracting davinci_emac.ko
Extracting display.ko
Extracting dm365mmap.ko
Extracting edmak.ko
Extracting evdev.ko
Extracting getjif.ko
Extracting h3ak.ko
Extracting i2ckey.ko
Extracting irqk.ko
Extracting mcu_spi.ko
Extracting mfrc522.ko
Extracting mmc_blk.ko
Extracting mmc_core.ko
Extracting mmc_drv.ko
Extracting mymemcpy.ko
Extracting pwm.ko
Extracting pwm_gpio.ko
Extracting Sensor.ko
Extracting sound.ko
Extracting spi.ko
Extracting spi_mcu.ko
Extracting touch_panel_ctrl.ko
Extracting vpbek.ko
Extracting vpfek.ko

Everything is Ok
/mnt/mtd/Config/ppp

7z ANSI-C Decoder 9.20 : Igor Pavlov : Public domain : 2010-11-18

Extracting sshd

Everything is Ok

7z ANSI-C Decoder 9.20 : Igor Pavlov : Public domain : 2010-11-18

Extracting VideoDaemon

Everything is Ok

7z ANSI-C Decoder 9.20 : Igor Pavlov : Public domain : 2010-11-18

