С заводской прошивкой работала.
Но как только проапгрейдил - началось.
Менял около 20-ти прошивок только через консольный шнурок.
Ни одна не подняла сию камеру.
И вот на последней прошивке на консоли стала выдавать такой рисунок и всё - не позволяет больше делать никаких манипуляций.
Код: Выделить всё
Checking DDR......OK
UBL Version: 1.43t(DM368 29/3/2012)
Oscillator: 24MHZ
ARM Rate: 270 MHZ
DDR Rate: 216 MHZ
BootMode: SPI
Starting SPI Memory Copy...
DONE
U-Boot 1.3.6 (jerry) (Apr 20 2012 - 10:24:18)
DRAM: 128 MB
SF: Got idcode 01 20 18
SF: Detected S25FL128P with page size 256, total 16 MB
In: serial
Out: serial
Err: serial
Ethernet PHY: GENERIC @ 0x05,id:221513
total gio 2
gio[22]=1
gio[25]=1
Fail: can't get cramfs super block.
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending throu
gh gateway 192.168.1.1
Filename 'upgrade_info_7db780a713a4.txt'.
Load address: 0x80100000
Loading: *
Retry count exceeded.
Failed to get info.txt
==>use default images
Wrong Image Format for bootm command
ERROR: can't get kernel image!
DHBOOT#
DHBOOT#
DHBOOT#
DHBOOT#
DHBOOT# U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6#####
U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1
.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6####
# U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot
1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##
### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Bo
ot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6
##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-
Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3
.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6#####
U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1
.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6####
# U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3.6##### U-Boot 1.3
Код: Выделить всё
DHBOOT# help
? - alias for 'help'
askenv - get environment variables from stdin
autoscr - run script from memory
base - print or set address offset
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
cpll - chang PLL multiplier
crc32 - checksum calculation
dhcp - invoke DHCP client to obtain IP/boot params
echo - echo args to console
erase - erase FLASH memory
flinfo - print FLASH memory information
flwrite - write data into FLASH memory
fsload - load binary file from a filesystem image
gpio init - set gionum to gioval
go - start application at address 'addr'
help - print online help
flwrite - write hwid into FLASH memory
id - set product id and save to flash
iminfo - print header information for application image
imxtract- extract a part of a multi-image
itest - return true/false on integer compare
lip - set local ip address but not save to flash
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
mac - set mac address and save to flash
md - memory display
meminit - memset 0xcc
memsize - set mem size
mii - MII utility commands
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol recover default env
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
saves - save S-Record file over serial line
setenv - set environment variables
sip - set server ip address but not save to flash
sleep - delay execution for some time
tftpboot- boot image via network using TFTP protocol
version - print monitor version
DHBOOT#
Код: Выделить всё
DHBOOT# printenv
bootargs=console=ttyS0,115200n8 root=/dev/mtdblock4 rootfstype=cramfs ,nolock mem=80M video=davincifb:vid0=OFF:vid1=OFF:osd0=OFF:osd1=OFF
bootcmd=fsload;bootm 80800000
bootdelay=3
baudrate=115200
bootfile="uImage"
single=0
da=protect off all;tftp 81a00000 dm365_ubl_boot_16M.bin.img;flwrite
dc=tftp 81a00000 custom-x.cramfs.img; flwrite
dr=tftp 81a00000 romfs-x.cramfs.img; flwrite
du=tftp 81a00000 user-x.cramfs.img; flwrite
dd=tftp 81a00000 data-x.cramfs.img; flwrite
dw=tftp 81a00000 web-x.cramfs.img; flwrite
up=tftp 81a00000 update.img; flwrite
tk=tftp 80800000 uImage; bootm 80800000
gionum=22.25
gioval=1.1
dh_com=0
autosip=192.168.254.254
autolip=192.168.1.108
autogw=192.168.1.1
autonm=255.255.255.0
armrate=270
HWID=080202400531842b
ID=LDP2A117142024
ethaddr=90:02:A9:0A:50:9F
dk=tftp 81a00000 kernel-x.cramfs.img
filesize=6BD140
fileaddr=81A00000
ipaddr=10.12.10.28
serverip=10.12.9.27
dh_keyboard=1
appauto=1
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 1.3.6 (jerry) (Apr 20 2012 - 10:24:18)
Environment size: 1012/16380 bytes
DHBOOT#